Carrier 39L specifications Control System, Pulse-Type Meter Wiring

Pulse-Type Meter (Fig. 67) Ð Monitors power usage, which is passed through the Carrier Comfort Network (CCN) for use by the loadshed module of the Building Supervisor. The meter must provide a dry contact signal (not exceeding 4 Hz maximum). Using a 2-conductor 20 AWG shielded twisted- pair conductor cable, connect one wire to terminal 35 of the option module and the other wire to terminal 36. Connect the drain wire to the ground lug inside the PIC control box and remove the drain wire and shield on the meter end of the cable. Tape to insulate, if required.

SIGNAL	CCN BUS CONDUCTOR	COMM1 PLUG
TYPE	INSULATION COLOR	PIN NO.
1	RED	1
Ground	WHITE	2
−	BLACK	3

If a cable with a different color scheme is selected, a simi- lar color code should be adopted for the entire network.

At each system element, the shields of its communication bus cables must be tied together. If the communication bus is entirely within one building, the resulting continuous shield must be connected to ground at only one point. See Fig. 69. If the communication bus cable exits from one building and enters another, the shields must be connected to ground at the lightning suppressor in each building where the cable enters or exits the building (one point only).

To connect the 39L or 39NX unit to the network, proceed as follows (Fig. 69):

1.Turn power to the PIC control box to OFF.

2.Remove the COMM1 plug from the processor module.

3.Cut the CCN wire and strip the ends of the RED, WHITE, and BLACK conductors.

4.Using a wire nut, connect the 2 drain wires together.

5.Insert and secure the 2 RED wires to terminal 1 of the COMM1 plug.

6.Insert and secure the 2 WHITE wires to terminal 2 of the COMM1 plug.

7.Insert and secure the 2 BLACK wires to terminal 3 of the COMM1 plug.

Field Wiring

Fig. 67 Ð Pulse-Type Meter Wiring

ELECTRIC HEATER Ð The electric heater is factory wired and installed and is controlled by the PIC processor and DSIO. There is no ®eld wiring or installation required.

CARRIER COMFORT NETWORK INTERFACE Ð The Carrier Comfort Network (CCN) communication bus wiring is supplied and installed by the electrical contractor. It con- sists of shielded, 3-conductor cable with drain wire.

The system elements are connected to the communication bus in a daisy-chain arrangement. The positive pin of each system element communication connector must be wired to the positive pins of the system element on either side of it; the negative pins must be wired to the negative pins; the sig- nal ground pins must be wired to signal ground pins. See Fig. 68 for location of the CCN communication plug (COMM1) on the processor module.

NOTE: Conductors and drain wire must be 20 AWG mini- mum, stranded tinned copper. Individual conductors must be insulated with PVC, PVC/nylon, vinyl, Te¯on, or polyeth- ylene. An aluminum/polyester 100% foil shield and an outer jacket of PVC, PVC/nylon, chrome vinyl, or Te¯on with a minimum operating temperature range of −20 C to 60 C is required. See Table below for cables that meet the requirements.

MANUFACTURER	CABLE NO.
Alpha	2413 or 5463
American	A22503
Belden	8772
Columbia	02525

When connecting the CCN communication bus to a sys- tem element, a color code system for the entire network is recommended to simplify installation and checkout. The fol- lowing color code is recommended:

Fig. 68 Ð CCN Sensor Plug and Communication

Plug Locations

OUTDOOR-AIR THERMOSTAT Ð Use ®eld-supplied, 2-conductor 20 AWG wire to connect the thermostat to the DSIO and terminal block in the PIC control box. See Fig. 70. Connect one wire between the thermostat and J3-1 on the DSIO. For 39NX units, connect a second wire be- tween the other thermostat terminal and TB3-9 (TB2-10 for 39L units). For 39NX units, connect a third wire between J3-2 on the DSIO and TB4-10 (TB2-9 on 39L units).

CONTROL SYSTEM

The control system consists of a processor module (Fig. 71), sensors, and controlled devices. Available options include a processor option module (Fig. 71), relay modules (Fig. 72), and local interface device.

64