Gigabyte GA-8I915P-MF user manual Dual Channel Technology DS Double Side, SS Single Side

Page 15

GA-8I915P-MF supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double up to 6.4GB/s.

GA-8I915P-MF includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4

If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel® chipset specifications.

1. Only one DDR memory module is installed: The Dual Channel Technology can't operate when only one DDR memory module is installed.

2. Two DDR memory modules are installed (the same memory size and type): The Dual Channel Technology will operate when two memory modules are inserted individually into Channel A and B. If you install two memory modules in the same channel, the Dual Channel Technology will not operate.

3. Three DDR memory modules are installed: Please note that The Dual Channel Technology will not operate when three DDR memory modules are installed; part of them will not be detected.

4. Four DDR memory modules are installed: If you install four memory modules at the same time, the Dual Channel Technology will operate only when those modules have the same memory size and type.

We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in order for Dual Channel Technology to work.

The following tables include all memory-installed combination types:

zFigure 1: Dual Channel Technology (DS: Double Side, SS: Single Side)

 

DDR 1

DDR 2

DDR 3

DDR 4

2 memory modules

DS/SS

X

DS/SS

X

 

X

DS/SS

X

DS/SS

4 memory modules

DS/SS

DS/SS

DS/SS

DS/SS

 

 

 

 

 

z Figure 2: Don't operate Dual Channel Technology (DS: Double Side, SS: Single Side)

 

DDR 1

DDR 2

DDR 3

DDR 4

1 memory module

DS/SS

X

X

X

 

X

DS/SS

X

X

 

X

X

DS/SS

X

 

X

X

X

DS/SS

2 memory modules

DS/SS

DS/SS

X

X

 

X

X

DS/SS

DS/SS

3 memory modules

DS/SS

DS/SS

DS/SS

X

 

DS/SS

DS/SS

X

DS/SS

 

DS/SS

X

DS/SS

DS/SS

 

X

DS/SS

DS/SS

DS/SS

 

 

 

 

 

English

- 15 -

Hardware Installation

Image 15
Contents GA-8I915P-MF Motherboard Product Manual Classification CopyrightTable of Content Install Drivers GA-8I915P-MF Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Technology DS Double Side, SS Single Side Install expansion cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE IDE Connector Fpanel Front Panel Jumper Pwrled Azaliafp Front Audio ConnectorCdin CD USB1 / FUSB2 Front USB Connector14 IR 13 F11394/F21394 Ieee 1394 ConnectorClrcmos Clear Cmos Comb Serial Port ConnectorBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F4 „ Set User Password „ Save & Exit Setup„ Exit Without Saving Standard Cmos Features TimeIDE Channel 0 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteOn-Chip Primary PCI IDE Integrated PeripheralsUSB Controller On-Chip Sata ModePata IDE Set to Sata Port 1/3 Set toOnboard H/W Onboard LAN Boot ROMUart Mode Select UR2 Duplex ModePower Management Setup Parallel Port ModeECP Mode Use DMA KB Power on Password Resume by AlarmPower On By Mouse Power On By KeyboardPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Memory Frequency For CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Clock RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Introduction of audio connectors Stereo Speakers Connection and Settings4 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English English English English English English English Taiwan Headquarters Contact UsChina Shanghai