Gigabyte GA-8I915P-MF user manual Part Two

Page 60

English

6.Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Load Fail-Safe Defaults (Y/N)?Set SupervisorY	Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7.Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu. System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features		Select Language
Advanced BIOS Features		Load Fail-Safe Defaults
Integrated Peripherals		Load Optimized Defaults
Power Management Setup	Save to CMOS and EXIT (Y/N)?Set SupervisorY		Password
PnP/PCI Configurations		Set User Password
PC Health Status		Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)		Exit Without Saving
ESC: Quit		F3: Change Language
F8: Dual BIOS/Q-Flash		F10: Save & Exit Setup
		Time, Date, Hard Disk Type...
	Press Y on your keyboard to save and exit.
Part Two:

Updating BIOS with Q-FlashTMUtility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTMutility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Top Performance
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

GA-8I915P-MF Motherboard

- 60 -

Image 60

Contents GA-8I915P-MF Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915P-MF Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Technology DS Double Side, SS Single Side Install expansion cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector Fpanel Front Panel Jumper Azaliafp Front Audio Connector PwrledUSB1 / FUSB2 Front USB Connector Cdin CD13 F11394/F21394 Ieee 1394 Connector 14 IRComb Serial Port Connector Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F4 „ Set User Password „ Save & Exit Setup„ Exit Without Saving Standard Cmos Features TimeIDE Channel 0 Master, Slave Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Sata Mode Pata IDE Set toSata Port 1/3 Set to USB ControllerOnboard LAN Boot ROM Uart Mode SelectUR2 Duplex Mode Onboard H/WPower Management Setup Parallel Port ModeECP Mode Use DMA Resume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode MB Intelligent TweakerM.I.TCPU Clock Ratio Memory Frequency ForLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Introduction of audio connectors Stereo Speakers Connection and Settings4 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English English English English English English English Contact Us Taiwan HeadquartersChina Shanghai