Gigabyte GA-8I915P-MF Drive a / Drive B, Floppy 3 Mode Support for Japan Area, Halt on, Memory

Page 33

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None

No floppy drive installed

360K, 5.25"

5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25"

5.25 inch AT-type high-density drive; 1.2M byte capacity

 

(3.5 inch when 3 Mode is Enabled).

720K, 3.5"

3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5"

3.5 inch double-sided drive; 1.44M byte capacity.

2.88M, 3.5"

3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled

Normal Floppy Drive. (Default value)

Drive A

Drive A is 3 mode Floppy Drive.

Drive B

Drive B is 3 mode Floppy Drive.

Both

Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on

the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

English

- 33 -

BIOS Setup

Image 33
Contents GA-8I915P-MF Motherboard Product Manual Classification CopyrightTable of Content Install Drivers GA-8I915P-MF Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Technology DS Double Side, SS Single Side Install expansion cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE IDE Connector Fpanel Front Panel Jumper Pwrled Azaliafp Front Audio ConnectorCdin CD USB1 / FUSB2 Front USB Connector14 IR 13 F11394/F21394 Ieee 1394 ConnectorClrcmos Clear Cmos Comb Serial Port ConnectorBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F4 „ Set User Password „ Save & Exit Setup„ Exit Without Saving Standard Cmos Features TimeIDE Channel 0 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory Protect Note CPU Enhanced Halt C1E NoteOn-Chip Primary PCI IDE Integrated PeripheralsPata IDE Set to On-Chip Sata ModeSata Port 1/3 Set to USB ControllerUart Mode Select Onboard LAN Boot ROMUR2 Duplex Mode Onboard H/WPower Management Setup Parallel Port ModeECP Mode Use DMA Power On By Mouse Resume by AlarmPower On By Keyboard KB Power on PasswordPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status MB Intelligent TweakerM.I.T CPU Smart FAN ModeCPU Clock Ratio Memory Frequency ForLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Introduction of audio connectors Stereo Speakers Connection and Settings4 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English English English English English English English Taiwan Headquarters Contact UsChina Shanghai