Gigabyte GA-8I915P-MF user manual MB Intelligent TweakerM.I.T, CPU Smart FAN Mode, CPU Clock Ratio

Page 43

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto

BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart

 

FAN control mode for it. (Default value)

Voltage

Set to Voltage when you use a CPU fan with a 3-pin fan power cable.

PWM

Set to PWM when you use a CPU fan with a 4-pin fan power cable.

In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables. However, some 4-pin CPU fan power cables are not designed following Intel 4-wire fans PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan speed.

2-7

MB Intelligent Tweaker(M.I.T.)

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

MB Intelligent Tweaker(M.I.T.)

 

 

 

CPU Clock Ratio

[15X]

 

 

Item Help

 

Memory Frequency For

[Auto]

 

Menu Level`

 

Memory Frequency (Mhz)

400

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Default

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

Memory Frequency For

Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue. for FSB(Front Side Bus) frequency=800MHz,

2.0

Memory Frequency = Host clock X 2.0.

2.66

Memory Frequency = Host clock X 2.66.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on "Memory Frequency For" item.

- 43 -

BIOS Setup

English

Image 43
Contents GA-8I915P-MF Motherboard Product Manual Classification CopyrightTable of Content Install Drivers GA-8I915P-MF Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel Technology DS Double Side, SS Single Side Install expansion cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE IDE Connector Fpanel Front Panel Jumper Pwrled Azaliafp Front Audio ConnectorCdin CD USB1 / FUSB2 Front USB Connector14 IR 13 F11394/F21394 Ieee 1394 ConnectorClrcmos Clear Cmos Comb Serial Port ConnectorBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F4 „ Save & Exit Setup „ Set User Password„ Exit Without Saving Time Standard Cmos FeaturesIDE Channel 0 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory Protect NoteOn-Chip Primary PCI IDE Integrated PeripheralsUSB Controller On-Chip Sata ModePata IDE Set to Sata Port 1/3 Set toOnboard H/W Onboard LAN Boot ROMUart Mode Select UR2 Duplex ModeParallel Port Mode Power Management SetupECP Mode Use DMA KB Power on Password Resume by AlarmPower On By Mouse Power On By KeyboardPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Memory Frequency For CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Clock RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Stereo Speakers Connection and Settings Introduction of audio connectors4 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English English English English English English English Taiwan Headquarters Contact UsChina Shanghai