Gigabyte GA-8I915P-MF Connectors Introduction, Center/Subwoofer Speaker Out, Side Speaker Out

Page 18

English

Center/Subwoofer Speaker Out

Connect the Center/Subwoofer speakers to this connector.

Side Speaker Out

Connect the side surround speakers to this connector.

You can use audio software to configure 2-/4-/6-/8-channel audio functioning.

1-7 Connectors Introduction

3

 

 

 

2

 

 

 

14

 

1

 

4

 

 

5

 

 

 

 

10

 

6

 

 

 

17

 

 

 

16

 

11

 

7

 

 

9

 

 

 

 

 

 

8

 

15

13

12

1)

ATX_12V

10)

AZALIA_FP

2)

ATX (Power Connector)

11)

CD_IN

3)

CPU_FAN

12)

F_USB1 / F_USB2

4)

SYS_FAN

13)

F1_1394 / F2_1394

5)

FDD

14)

IR

6)

IDE

15)

COMB

7)

S_ATA0 / S_ATA1 / S_ATA2 / S_ATA3

16)

CLR_CMOS

8)

F_PANEL

17)

BAT

9)

PWR_LED

 

 

GA-8I915P-MF Motherboard

- 18 -

Image 18
Contents GA-8I915P-MF Motherboard Copyright Product Manual ClassificationTable of Content Install Drivers GA-8I915P-MF Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUUse of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel Technology DS Double Side, SS Single Side Install expansion cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector Fpanel Front Panel Jumper Azaliafp Front Audio Connector PwrledUSB1 / FUSB2 Front USB Connector Cdin CD13 F11394/F21394 Ieee 1394 Connector 14 IRComb Serial Port Connector Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F4 „ Set User Password „ Save & Exit Setup„ Exit Without Saving Standard Cmos Features TimeIDE Channel 0 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory Protect Note CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteIntegrated Peripherals On-Chip Primary PCI IDESata Port 1/3 Set to On-Chip Sata ModePata IDE Set to USB ControllerUR2 Duplex Mode Onboard LAN Boot ROMUart Mode Select Onboard H/WPower Management Setup Parallel Port ModeECP Mode Use DMA Power On By Keyboard Resume by AlarmPower On By Mouse KB Power on PasswordPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Clock Ratio CPU Smart FAN ModeMB Intelligent TweakerM.I.T Memory Frequency ForLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Introduction of audio connectors Stereo Speakers Connection and Settings4 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting English English English English English English English English English Contact Us Taiwan HeadquartersChina Shanghai