Gigabyte GA-7N400S-L user manual I/O Back Panel Introduction

Page 16

English

1-7 I/O Back Panel Introduction

*

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS ven dor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COM A / COM B (Serial Port)

Connects to serial-based mouse or data processing devices.

LAN Port *

The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Connect the stereo speakers or earphone to this connector.

MIC In

Microphone can be connected to MIC In jack.

You can use audio software to configure 2-/4-/6-channel audio functioning.

* Only for GA-7N400S-L.

GA-7N400S(-L) Motherboard

- 16 -

Image 16
Contents GA-7N400S / GA-7N400S-L Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-7N400S/GA-7N400S-L Motherboard Layout GA-7N400SBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary ALC655 CodecInstallation of the CPU and Heatsink Set System Clock ClkswInstallation of the CPU Installation of the HeatsinkInstallation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Surcen Surround Center ConnectorSpdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector 17 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E17 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstAdvanced Chipset Features Integrated Peripherals On-Chip Primary PCI IDEOn-Chip Secondary PCI IDE Serial ATASata DMA Transfer RAID ConfigSata Spread Spectrum Uart Mode Select UR2 Duplex ModeOnChip USB USB Keyboard SupportParallel Port Mode ECP Mode Use DMAOnboard Parallel port Game Port AddressPower Management Setup Resume by AlarmPME Event Wake Up ModemRingOnPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations INTCurrent System/CPU Temperature PC Health StatusCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the nVIDIA RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Channel Audio Setup 4 2- / 4- / 6- Channel Audio Function IntroductionEnglish Basic 6 Channel Audio Setup English Basic & Advanced 6 Channel Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introduction Introduction of audio connectorsAuto-detecting Manual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai