Gigabyte GA-7N400S-L Onboard Parallel port, Parallel Port Mode, ECP Mode Use DMA, Midi Port IRQ

Page 38

English

Onboard Parallel port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port.

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port. (Default value)

ECP+EPP

Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

3

Set ECP Mode Use DMA to 3. (Default value)

1

Set ECP Mode Use DMA to 1.

Game Port Address

201

Set Game Port Address to 201. (Default value)

209

Set Game Port Address to 209.

Disabled

Disable this function.

Midi Port Address

300

Set Midi Port Address to 300.

330

Set Midi Port Address to 330.

Disabled

Disable this function. (Default value)

Midi Port IRQ

 

5

Set Midi Port IRQ to 5.

10

Set Midi Port IRQ to 10. (Default value)

GA-7N400S(-L) Motherboard

- 38 -

Page 37 Page 39
Image 38
Page 37 Page 39
Contents GA-7N400S / GA-7N400S-L Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-7N400S/GA-7N400S-L Motherboard Layout GA-7N400SBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary ALC655 CodecInstallation of the CPU and Heatsink Set System Clock ClkswInstallation of the CPU Installation of the HeatsinkInstallation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Surcen Surround Center ConnectorSpdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector 17 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E17 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupStandard Cmos Features TimeHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekPassword Check Init Display FirstAdvanced Chipset Features On-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Serial ATASata Spread Spectrum RAID ConfigSata DMA Transfer OnChip USB Uart Mode SelectUR2 Duplex Mode USB Keyboard SupportOnboard Parallel port Parallel Port ModeECP Mode Use DMA Game Port AddressPME Event Wake Up Power Management SetupResume by Alarm ModemRingOnKB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations INTCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current System/CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the nVIDIA RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Channel Audio Setup 4 2- / 4- / 6- Channel Audio Function IntroductionEnglish Basic 6 Channel Audio Setup English Basic & Advanced 6 Channel Audio Output Mode Notes Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing Introduction Manual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai
Top Page Image Contents