Gigabyte GA-7N400S-L user manual Sata DMA Transfer, Sata Spread Spectrum, RAID Config

Page 36

English

SATA DMA Transfer

Enabled	Enable Serial ATA transfer function. (Default value)
Disabled	Disable this function.

SATA Spread Spectrum

Enabled	Enable Serial ATA spread spectrum function.
Disabled	Disable this function. (Default value)

RAID Config

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

RAID Config

IDE Channel0 Master RAID		[Disabled]		Item Help
IDE Channel0 Slave RAID		[Disabled]		Menu Level`
IDE Channel1 Master RAID		[Disabled]
IDE Channel1 Slave RAID		[Disabled]
SATA Primary Master RAID		[Disabled]
SATA Secndry Master RAID		[Disabled]
KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
F5: Previous Values		F6: Fail-Save Defaults		F7: Optimized Defaults
IDE Channel0 Master RAID
Enabled	Enable first master channel IDE RAID function.
Disabled	Disable this function. (Default value)
IDE Channel0 Slave RAID
Enabled	Enable first slave channel IDE RAID function.
Disabled	Disable this function. (Default value)
IDE Channel1 Master RAID
Enabled	Enable secondary master channel IDE RAID function.
Disabled	Disable this function. (Default value)
IDE Channel1 Slave RAID
Enabled	Enable secondary slave channel IDE RAID function.
Disabled	Disable this function. (Default value)
SATA Primary Master RAID
Enabled	Enable first SATA RAID function.
Disabled	Disable this function. (Default value)
SATA Secndry Master RAID
Enabled	Enable secondary SATA RAID function.
Disabled	Disable this function. (Default value)

GA-7N400S(-L) Motherboard

- 36 -

Image 36

Contents GA-7N400S / GA-7N400S-L Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-7N400S/GA-7N400S-L Motherboard Layout GA-7N400SBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary ALC655 CodecInstallation of the CPU and Heatsink Set System Clock ClkswInstallation of the CPU Installation of the HeatsinkInstallation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Surcen Surround Center ConnectorSpdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector 17 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E17 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupStandard Cmos Features TimeFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstAdvanced Chipset Features Integrated Peripherals On-Chip Primary PCI IDEOn-Chip Secondary PCI IDE Serial ATARAID Config Sata DMA TransferSata Spread Spectrum Uart Mode Select UR2 Duplex ModeOnChip USB USB Keyboard SupportParallel Port Mode ECP Mode Use DMAOnboard Parallel port Game Port AddressPower Management Setup Resume by AlarmPME Event Wake Up ModemRingOnPower On by Mouse Power On by KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations INTCurrent System/CPU Temperature PC Health StatusCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the nVIDIA RAID Bios Entering the RAID Bios SetupUsing the Define a New Array Window Selecting the RAID ModeSelecting the Striping Block Size Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Channel Audio Setup 4 2- / 4- / 6- Channel Audio Function IntroductionEnglish Basic 6 Channel Audio Setup English Basic & Advanced 6 Channel Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntroductionAuto-detecting Manual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai