Gigabyte user manual GA-7N400S/GA-7N400S-L Motherboard Layout

Page 6

GA-7N400S/GA-7N400S-L Motherboard Layout

KB_MS

R_USB

		COMA
			LPT
		COMB
					F AUDIO CD IN
	INMIC	OUTLINE	INLINE		F AUDIO CD IN
	USB		LAN*

ATX_12V

SOCKET A

nVIDIA nForce 2 Ultra 400

CLK_SW


DDR1						DDR2

GA-7N400S

DDR3

ATX

SUR_CEN

RTL8100C*	AUX_IN

SPDIF_IO

CPU_FAN

AGP

IDE2 IDE1

PCI1

nVIDIA SATA1

PCI2nForce 2

MCP RAID

CODEC

PCI3

SATA0

-L*

IT8712

PCI4	BIOS	BAT
	BIOS	BAT
		CLR_CMOS

PCI5		FDD

	PWR_LED

IR

* Only for GA-7N400S-L.

F_USB1 F_USB2

F_PANEL SYS_FAN

- 6 -

Image 6

Contents GA-7N400S / GA-7N400S-L Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-7N400S/GA-7N400S-L Motherboard Layout GA-7N400SBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary ALC655 CodecInstallation of the CPU and Heatsink Set System Clock ClkswInstallation of the CPU Installation of the HeatsinkInstallation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Surcen Surround Center ConnectorSpdifio Spdif In / Out Connector USB1 / FUSB2 Front USB Connector 17 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E17 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupStandard Cmos Features TimeHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekPassword Check Init Display FirstAdvanced Chipset Features On-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Serial ATARAID Config Sata DMA TransferSata Spread Spectrum OnChip USB Uart Mode SelectUR2 Duplex Mode USB Keyboard SupportOnboard Parallel port Parallel Port ModeECP Mode Use DMA Game Port AddressPME Event Wake Up Power Management SetupResume by Alarm ModemRingOnKB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations INTCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current System/CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Serial ATA Bios Setting Utility Introduction RAID LevelsConfiguring the nVIDIA RAID Bios Entering the RAID Bios SetupSelecting the Striping Block Size Using the Define a New Array WindowSelecting the RAID Mode Assigning the DisksCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers Channel Audio Setup 4 2- / 4- / 6- Channel Audio Function IntroductionEnglish Basic 6 Channel Audio Setup English Basic & Advanced 6 Channel Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntroductionAuto-detecting Manual setting Troubleshooting AMI Bios Beep CodesEnglish Contact Us Taiwan HeadquartersChina Shanghai