Gigabyte GA-7N400S Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 55

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

English

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title
			Save Settings to CMOS
			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

- 55 -

Appendix

Image 55

Contents GA-7N400S / GA-7N400S-L Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-7N400S GA-7N400S/GA-7N400S-L Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC655 Codec Feature SummarySet System Clock Clksw Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of the CPUInstallation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Surcen Surround Center Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector 17 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E17 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordTime Standard Cmos FeaturesMemory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBoot Up Floppy Seek Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceInit Display First Password CheckAdvanced Chipset Features Serial ATA Integrated PeripheralsOn-Chip Primary PCI IDE On-Chip Secondary PCI IDESata DMA Transfer RAID ConfigSata Spread Spectrum USB Keyboard Support Uart Mode SelectUR2 Duplex Mode OnChip USBGame Port Address Parallel Port ModeECP Mode Use DMA Onboard Parallel portModemRingOn Power Management SetupResume by Alarm PME Event Wake UpAC Back Function Power On by MousePower On by Keyboard KB Power on PasswordINT PnP/PCI ConfigurationsCurrent CPU/SYSTEM FAN Speed RPM Current System/CPU TemperaturePC Health Status Current Voltage V Vcore / DDR25V / +3.3V / +12VLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities Xpress Recovery IntroductionWhat is Xpress Recovery ? How to use the Xpress RecoveryF9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the nVIDIA RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeCompleting the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 4 2- / 4- / 6- Channel Audio Function Introduction Channel Audio SetupEnglish Basic 6 Channel Audio Setup English Basic & Advanced 6 Channel Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introduction Introduction of audio connectorsAuto-detecting Manual setting AMI Bios Beep Codes TroubleshootingEnglish Taiwan Headquarters Contact UsChina Shanghai