Tripp Lite B022-U08-IP owner manual Local Console OSD F4 Administration ADM

Page 28

7. Administration (continued)

7.1.3 Local Console OSD F4 Administration (ADM) Page

This Administrator-onlypage allows administrators to configure the settings of the KVM switch. To change a setting:

1)Double-click on it, or highlight it and press the [Enter] key.

2)After you select an item, a submenu with more choices will appear. To make a selection, double-click on a choice or highlight it and press the

[Enter] key.

The settings in the F4 ADM page are explained in the following table:

Setting

Description

 

 

SET IP

This page allows administrators to set the network settings for the KVM.

ADDRESS

DHCP: The first field allows you to enable or disable DHCP. When enabled, the KVM is assigned an IP address by the DHCP

 

server. This setting is enabled by default. To disable the DHCP setting and set up a fixed IP address, press the [Spacebar] key.

 

Once the DHCP is disabled, you will be allowed to edit the remaining fields in the SET IP ADDRESS page. In the remaining fields,

 

enter in the IP Address, Subnet Mask and Default Gateway you want to assign to the KVM switch. When these fields have been

 

populated, press the [Esc] key to exit and pull up a prompt asking if you wish to save the settings you just entered. If you do not

 

wish to save the settings, press the [N] key. If you do wish to save the settings, press the [Y] key. Upon pressing the [Y] key, the

 

settings will be saved and the KVM will be reset.

 

Note: Only an IPv4 address can be assigned using the Local Console OSD. To assign an IPv6 address, use the Web Management

 

Interface or Remote OSD. This page only allows you to set a fixed IP address or enable IP address assignment via DHCP server.

 

It does not allow you to set the HTTP, HTTPS and Program access ports, assign a DNS server address, or edit the IP Installer

 

settings. To set ports and assign a DNS server address, you can use the Web Management Interface or Remote OSD. To edit the

 

IP Installer settings, you must use the Web Management Interface.

 

 

SET LOGOUT

If there is no input from the console for the amount of time set here, the user will be logged out, requiring them to enter their

TIMEOUT

username and password to regain access to the KVM. This can be set from 0 to 180 minutes, with 0 disabling the function. Simply

 

type in the desired time frame and hit the [Enter] key to save your change. This is disabled (0) by default. Note: The Timeout

 

function can only be set in the Web Management Interface and the Local Console OSD.

 

 

EDIT PORT

This function allows administrators to give each port a unique name, making it easier to find the computer you want to access. To

NAMES

add/edit a port name, do the following:

 

1. Select the port by double-clicking on it, or by highlighting it and hitting the [Enter] key.

 

2. A name field will appear at the bottom of the screen. Add or edit the port name and hit the [Enter] key to save the change. To exit

 

without saving the change, hit the [Esc] key.

 

Port names can have a maximum of 12 characters, including any combination of letters and numbers (A-Z,0-9), and the following

 

characters: Asterisk [*], Parentheses [()], Plus [+], Minus [-],Colon [:], Comma [,], Question Mark [?], Period [.], Forward Slash [/]

 

and Space. Port names are NOT case sensitive. They will always display as uppercase in the OSD.

 

 

RESTORE

This allows the Administrator to restore all OSD settings to their factory default values except for the network settings, port names

DEFAULT

and username/passwords. When this function is accessed, a prompt will appear asking if you wish to restore the default settings. If

VALUES

yes, type in a Y and hit the [Enter] key. If no, press the [Esc] key to go back to the previous menu.

 

 

CLEAR THE

This function allows the Administrator to clear all of the port names that have been entered. As with the RESTORE DEFAULT­

NAME LIST

VALUES, you will be prompted upon accessing this function. If you wish to clear the name list, type in a Y and hit the [Enter] key.

 

If not, press the [Esc] key to go back to the previous menu.

 

 

ACTIVATE

Turns the beeper sound ON or OFF. Type in Y to turn the Beeper sound on, or N to turn it off. You do not need to hit the [Enter]

BEEPER

key after typing in Y or N, the change will be made automatically.

 

 

SET QUICK

Administrators can use this function to mark ports as Quick View ports. This provides a way to customize which ports are

VIEW PORTS

displayed in the OSD main menu, and which are accessible in Auto Scan and Skip Modes. To set ports as Quick View ports, do

 

the following:

1.Highlight the desired port and hit the [Enter] key, or click on it using the touchpad.

2.Press the [Spacebar] to toggle Quick View status ON/OFF. An icon will appear in the QV column next to the selected port

when Quick View status is turned on.

Once Quick View ports are set, the OSD main page can be set up to display only Quick View ports, or only Quick View ports that are powered ON. Administrators can also set it up so that only Quick View ports, or powered on Quick View ports, are accessible in Auto Scan or Skip Modes.

RESET

This function is used when you change the position of one of the KVM stations in a daisy chain. When you change the position­ of

STATION IDs

the station, the OSD does not recognize the change, and will not automatically update the main menu to display the stations in

 

correct order. When this function is used, the KVM will scan the entire installation and update the station numbers accordingly.

 

The port names of the affected stations will be kept; however, you will need to manually update all other settings (SET

 

ACCESSIBLE PORTS, SET QUICK VIEW PORTS, etc.).

 

 

SET

This allows the Administrator to set the operating system for the port to match that of the connected computer. To set the

OPERATING

operating system, do the following:

SYSTEM

1. Highlight the desired port or click on it using the touchpad.

 

2. Press the [Spacebar] to toggle between four options; WIN, MAC, SUN and OTHER. Each port is set to WIN by default.

 

3. You do not need to press the [Enter] key to save this setting.

 

 

FIRMWARE

Note: The KVM has two sets of firmware, one to control IP Access and another to control the KVM’s Mainboard, Input/Output

UPGRADE

Ports and Keyboard. The IP Access firmware must be updated via the Web Management Interface or Remote OSD. The KVM

 

Mainboard, Input/Output Ports and Keyboard firmware must be updated via the local console OSD.

 

In order to upgrade the KVM Mainboard, Input/Output Ports and Keyboard firmware, Firmware Upgrade Mode must be invoked

 

via this setting.

 

When you select this option, the firmware version numbers are displayed on the OSD screen, and a prompt will ask if you wish to

 

continue with a firmware upgrade. If yes, type in Y. If no, type in N.

28

Image 28
Contents Model # B022-U08-IP Table of Contents Package Contents FCC InformationUser Notice IntroductionSystem Requirements Supported operating systems are shown in the table, belowComponents General Safety Instructions InstallationRack Mounting Safety Instructions Single Stage Installation Rack Mounting InstructionsGrounding Standard Rack MountingMulti-Stage Daisy-chain Installation Network Setup-IP Address ConfigurationIP Installer DNS server field is optional Installation Powering Off and Restarting Local Console LoginKVM Operation Sharing USB Peripheral DevicesLocal Console Port Access Key DescriptionInvoking the Hotkey Mode When Hotkey Mode has been invokedPort Control Hotkeys Other HotkeysAuto Scan Mode Skip ModeComputer Keyboard/Mouse Reset Hotkey Mode Invocation SequenceLogging Into the KVM over IP Hotkey Operation Hotkey Command DescriptionHotkey Summary Table Logging In via the AP Windows Client Web Browser and Non-Browser Remote Port Access Port Access via Remote OSD Icon DescriptionMouse Synchronization Procedures WindowsWindows XP / Server 2003 / Vista Windows MERemote Auto Scan Hotkey Setup Configuring the HotkeysVideo Settings Action Hotkey DescriptionGamma Adjustment Setting DescriptionVideo Auto Sync Gray ScaleUser List Panel Compose PanelMessage Display Panel Ctrl-Alt-DelLocal OSD Remote OSD AdministrationUser Local Console OSD ALLPort that is currently active Local Console OSD F4 Administration ADM Local Console Firmware Upgrade Firmware Upgrade Recovery Remote OSDRemote OSD Configuration Tab General Information User ManagementUser Management Port Access Network Access PortsUser Management Permissions NetworkAccess Rights AnmsCheck the Enable Ldap Authentication checkbox Anms LDAP/S ConfigurationInstall the Windows Support Tools Install the Active Directory Schema Snap-InAdministration Permission Attribute Value Access Rights DescriptionCharacter Description OpenLDAP Server Installation OpenLDAP Server ConfigurationAnms OpenLDAP Server \Program Files\OpenLDAPCustomizing the OpenLDAP Schema Ldap Data StuctureUsing the New Schema Anms Log Server SettingsSecurity Default Webpage Name SecurityCustomization Firmware Upgrade Customization Login FailuresCustomization Working Mode Customization Mouse Sync ModeReset on Exit Reset Default ValuesWeb Management Interface Customization I/OAccess Ports IP Address and DNS ServerIP Installer Settings Default Webpage NameRadius Settings LDAP/S Server Configuration Run Adsi Edit. Installed as part of the Support Tools Permission Attribute Value OpenLDAP Server OpenLDAP Server InstallationStarting the Open Ldap Server Log Server Settings Ldap Data StructureLogin Failure Client Timeout ControlPermissions Mouse Sync Mode Working ModeReset Backup Configuration / User Accounts Firmware UpgradeRestore Configuration / User Accounts Log Server ConfigureMenu Bar Events OptionsHelp Log Server Main ScreenList Panel Event PanelSpecifications Specification B022-U08-IPOSD Default Settings Keyboard EmulationMac Keyboard Sun KeyboardWarranty Registration FCC Notice, Class a
Related manuals
Manual 16 pages 37.5 Kb