Moxa Technologies NE-4100 user manual Pin Assignments, RXD1

Page 10

NE-4100 Series User’s Manual

Panel Layout and Pin Assignments

Pin Assignments

NE-4100T

Pin	Signal

1	ETx+

2	ETx-

3	ERx+

4	ERx-

5	10M LED

6	TXD

7	RXD

8	RTS

9	CTS

10	Reset

11	GND

12	GND

13	TXD1*

Pin	Signal

14	PIO0

15	PIO1

16	PIO2

17	PIO3

18	100M LED

19	DCD

20	DSR

21	DTR

22	GND

23	Ready LED

24	+5V

25	+5V

26	RXD1*

*Pins 13 and 26 control the NE-4100-ST Debug Serial COM Port’s TXD and RXD signals. The location of the Serial COM Port is shown in the figure on the previous page. This Serial COM Port is not needed during normal operation. However, once the network fails and you wish to configure your NE-4100T, you can connect the Debug Serial COM Port, and then use the serial console to configure your NE-4100T.

						Ethernet Signals:		ETx+, ETx-, ERx+, ERx-
	NOTE		NE-4100T Serial Signals:					TXD, RXD, RTS, CTS, DCD, DSR, DTR
						LED Controls:		10M LED, 100M LED, Ready LED

							NE-4100-ST Serial Port Pinouts
DB9 Male Connector for serial console								DB9 Male Connector for Connecting Serial Devices
	Pin	Signal							Pin	Signal

2			RXD	5				1		DCD		5
3			TXD	5				2		RXD		5
												4				8
												4
5			GND	3				3		TXD		3

																7
				2				4		DTR		2				7
				2								2				6
												1				6
								5		GND


								6		DSR
								7		RTS
								8		CTS

2-3

Image 10

Contents NE-4100 Series User’s Manual Sixth Edition, AprilCopyright Notice Table of Contents Chapter Configuring Windows Administrator Introduction Product Features Package ChecklistOverview Product Specifications Panel Layout and Pin Assignments NE-4120 Series/NE-4120-STNE-4100T NE-4100T/NE-4100-STPanel Layouts NE-4100-STPin Assignments RXD1NE-4100-ST LED Indicators Block DiagramLED Name LED Color LED Function NE-4110A NE-4110 Series/NE-4110-STNE-4110S NE-4110-ST evaluation board for NE-4110 SeriesEthernet Port Pinouts for NE-4110S/A Serial Header Pinouts J1 for NE-4110SSerial Header Pinouts J1 for NE-4110A DIO and LED Header Pinouts J2 for NE-4110S/ANE-4110S Block Diagram Block DiagramsNE-4110A Block Diagram NE-4110-ST LED Indicators Top Panel of NE-4120A NE-4120 Series/NE-4120-STTop Panel of NE-4120S NE-4120-ST evaluation board for NE-4120 SeriesSerial Header Pinouts J1 for NE-4120S Serial Header Pinouts J1 for NE-4120ANE-4120S Block Diagram NE-4120A Block DiagramNE-4120-ST LED Indicators Getting Started Wiring Requirements Attaching NE-4100T to the Evaluation BoardAttaching NE-4110 Series to the Evaluation Board Attaching NE-4120 Series to the Evaluation BoardCircuit Pad for External Connection Connecting to a Serial Device Connecting the PowerConnecting to the Network DI/O SettingsDigital Output LED Circuit Design Selecting the Interface JP2Choosing the Proper Operation Mode TCP Server Mode TCP Client Mode UDP ModeReal COM Mode Initial IP Address Configuration ARPDefault IP address Factory Default IP AddressNE-4100 Series Administration Suite Initializing NE-4100 Series Module’s IP AddressTelnet Console Page Serial Console 19200, n, 8 Web Console Configuration Opening Your Browser Server name Basic SettingsTime zone Setting Factory Default Necessity Time serverMethod Function Definition Network SettingsIP Address IP configuration Setting Factory Default Necessity 255.255.255.0 RequiredSetting Factory Default Necessity None Optional GatewayLocation Community nameContact Auto report to IPSerial Settings Operating Settings TCP Server ModeMax connection 2 to Max connectionMax. connection DelimiterCommand port Real COM ModeSetting Factory Default Necessity 4001 Required Setting Factory Default Necessity 966 OptionalNE-4100 Series User’s Manual Web Console Configuration TCP Client Mode Destination IP address 1/2/3/4 UDP Mode TCP connection onLocal Listen port # Any host can access the NE-4100 Accessible IP Settings# Hosts on a given subnet can access the NE-4100 Allowable Hosts Input formatAuto Warning Settings Mail and Snmp TrapEvent Type Digital IO DIO MonitorLoad Factory Defaults Change PasswordSave/Restart Configuring Windows Administrator Monitor Port Monitor COM MappingInstalling Network Enabler Administrator NE-4100 Series User’s Manual Web Console Configuration Starting the Configuration Broadcast SearchNE-4100 Series User’s Manual Web Console Configuration Unlock Password Protection Blank LockUnlock FixedConfiguring NE-4100 Upgrading the Firmware Export/Import Monitor Select Add Target NE-4100 Series User’s Manual Web Console Configuration NE-4100 Series User’s Manual Web Console Configuration Port Monitor COM Mapping On-line COM MappingSelect COM Setting to modify COM No., default setting, etc NE-4100 Series User’s Manual Web Console Configuration Off-line COM Mapping SW Reset Function NE-4100 Series User’s Manual SW Reset Function TCP Socket Application Service Well Known Port NumbersUDP Socket Application Service NE-4100 Series User’s Manual Well Known Port NumbersNeci Library ACK Packet Format Length Bytes Header Data DIO CommandsCommand Packet Format Length Bytes Header Data Data Structure DefinitionCommand Code Usage Reading Single DIO Parameters Writing a Single DIO ParametersNE-4100 Series User’s ManualDIO Commands Reading Multiple DIOsWriting Multiple DIOs Snmp Agent with MIB II & RS-232 Like Group System MIB Interfaces MIB Address Translation MIBService Information Moxa Internet Services Following services are providedMoxa Product & NE-4100T Problem Report FormSerial Number Product Return Procedure