Pelco FR85011A manual Troubleshooting, Video Present LED

Page 24

Troubleshooting

LED indicators on the front panel of the FT85011A transmitter/FR85011A receiver (refer to Figure 2) allow you to monitor signal status, laser status, data activity, and operating power. Table C provides information about the front-panel indicators and associated troubleshooting guidelines .

Table C. Troubleshooting with Front-Panel Indicators

Indicator Color

Meaning

Possible Cause

Corrective Action

 

 

 

 

 

Power LED (Pelco badge)

 

 

 

 

 

Blue Pelco logo

Power is being

No action required.

lights.

applied to the

 

 

 

module.

 

 

 

 

 

 

Blue Pelco logo

Power is not being

Power connection is faulty.

Check power connection.

does not light.

applied to the

 

If module is rack mounted,

 

module.

 

reseat module or power

 

 

 

supply as necessary.

 

 

 

 

 

 

Power supply has failed.

Replace power supply.

 

 

 

 

 

 

Loss of power occurs due to

Check circuit breakers, fuses,

 

 

tripped circuit breakers,

or electrical service as

 

 

blown fuses, or faulty

necessary.

 

 

electrical service.

 

 

 

 

 

Video Present LED

Green

Incoming video

No action required.

 

signal is present on

 

 

 

the channel.

 

 

 

 

 

 

Red on transmitter

Incoming video

Video source is not

Check power connection to

 

signal is not present

powered on.

the video source.

 

on the channel.

 

 

 

Video source is not

Check BNC connections.

 

 

 

 

connected to the

 

 

 

transmitter.

 

 

 

 

 

 

 

Coaxial cable is defective.

Replace cable.

 

 

 

 

Red on receiver

Incoming video

Optical signal is not being

Refer to the Optic Fault LED

 

signal is not present

received from the trans-

section in this table.

 

on the channel.

mitter. Optic Fault LED is

 

 

 

also red.

 

 

 

 

 

 

 

Video source is not

Check power connection to

 

 

powered on.

the video source.

 

 

 

 

 

 

Video source is not

Check BNC connections.

 

 

connected to the

 

 

 

transmitter.

 

 

 

 

 

 

 

Coaxial cable connected to

Replace cable.

 

 

the transmitter is defective.

 

 

 

 

 

 

 

 

(Continued on next page)

24

C2604M (7/06)

Image 24
Contents Fiber Transmitter Receiver Page Contents List of IllustrationsList of Tables Important Safety Instructions Risk of Electric Shock Do not Open Regulatory Notices Radio and Television InterferenceProduct Overview DescriptionAddition, note the following Models Multimode ModelsSingle-Mode Models Front Panel Data TX LED Data RX LED Video Present LEDRear Panel Installation Package ContentsData Communication Setup Data Communication Switch Setting Mounting Mounting the TRANSMITTER/RECEIVER Into a RackMounting the Transmitter/Receiver Using the Wall Clip Figures 7-12 for Wiring Diagrams Coaxial Cable ConnectionsWire Bi-PhasePin RS-485 RS-232 RS-422RS-232 Data Communication Wiring Device a Receiver RS-485 2-Wire Half Duplex Data Communication Wiring RS-485 4-Wire Full Duplex Data Communication Wiring Manchester Data Communication Wiring Bi-Phase Data Communication Wiring Troubleshooting Video Present LEDMeaning Possible Cause Corrective Action Optic Fault LED SpecificationsMeaning Possible Cause Corrective Action Data Tx LED Data Rx LEDSpecifications VideoModel No Optical Maximum Laser CompatibleReceivers Wavelength Model No Optical Maximum Laser FR85011A ReceiverC2604M 7/06 Product Warranty and Return Information ISO9001