Sun Microsystems 4500/3 manual # usr/sbin/ping -I 5

Page 33

6.Terminate your tip session by entering ~ . (tilde and period). Power-cycle the terminal concentrator to enable the IP address changes and wait at least two minutes for the terminal concentrator to activate its network.

monitor:: ~ .

Note –Double-check to ensure that the Ethernet hub is connected to the local area network. An RJ-45 cable must connect the Ethernet hub to the administration network backbone.

a.Disconnect the RJ-45 serial cable (Part No. 5121A) from Port 1 of the terminal concentrator and from the Sun workstation.

b.Reconnect the serial cable (Part No. 9524A) back into Port 1 of the terminal concentrator.

Note –At this time, the cluster configuration should be cabled as originally shipped from the factory.

7.From the Sun workstation, verify that the terminal concentrator responds to the new IP address:

#usr/sbin/ping -I 5 148.212.87.62

PING 148.212.87.62: 56 data bytes

64 bytes from scotch (148.212.87.62): icmp_seq=0. time=1. ms

64 bytes from scotch (148.212.87.62): icmp_seq=1. time=0. ms

64 bytes from scotch (148.212.87.62): icmp_seq=2. time=0. ms

64 bytes from scotch (148.212.87.62): icmp_seq=3. time=0. ms ^C

Note –The Sun workstation must be connected to the same subnet to which the terminal concentrator was configured.

Chapter 2 The Cluster Platform 4500/3 System 21

Image 33

Contents Cluster Platform 4500/3 User’s Guide Please Recycle Contents Laptop Settings to Access Monitor Mode Figures Vi Cluster Platform 4500/3 User’s Guide July Management Server Connections TablesViii Cluster Platform 4500/3 User’s Guide July Related Documentation PrefaceTypographic Conventions Accessing Sun Documentation Online Shell PromptsOrdering Sun Documentation Sun Welcomes Your Comments Tools for Reading Online Documentation IntroductionAdobe Acrobat Reader Man Command Netscape Navigator BrowserAnswerBook2 Server Solaris Documentation Cluster Platform 4500/3 User’s Guide July Cluster Platform 4500/3 System Task Overview Your Integrated System0012e2004c4b 1Ethernet IP Address Worksheet Hardware ComponentsNetwork Administration Software Components 2Cluster Platforms I/O Board PlacementCluster Platform 4500/3 System Management Server T3 No data T3 No mirror Cluster Platform Component Location 4Cluster Platform Rack Placement 2Cluster Platform Rack Components Power and Heating Requirements4Cluster Platform Cables Cabling the System5Cluster Platform Internal Cabling Customizing the Terminal Concentrator Customizing the Cluster Platform 4500/3Configure the terminal concentrator device Cluster Platform 4500/3 User’s Guide July # usr/sbin/ping -I 5 # telnet Gateway Net default gateway 148.212.87.248 metric 1 active Ok setenv auto-boot? true Ok boot disk0 From the Sun workstation, access the terminal concentratorChoose a specific localization Select the appropriate terminal emulation Select the primary network interface Select Dynamic Host Configuration Protocol Dhcp servicesEnter the IP address of the management server Enter the name of the management serverDeselect IPv6 support Deselect and confirm Kerberos security Select and confirm a naming serviceSelect a subnet membership Select a netmask Select the time zone and region to reflect your environment Select the appropriate time zone and regionSet the date and time, and confirm all information Select a secure root passwordAdd the cluster environment name Add the router name and IP addressEnter the terminal concentrator name node names will follow Add the cluster node names and IP addressesCluster Platform 4500/3 User’s Guide July Cluster Platform 4500/3 System Starting the Cluster Console Telnet send brk ok 7Cluster Nodes Console Windows 8Cluster Console Window Installing the Software Stack on Both Cluster NodesBefore You Begin Recovery Cluster Platform 4500/3 RecoveryInstalling the Recovery CD Recovery CD-ROMsBoot the system from the CD-ROM Select a CD-ROM drive from the menu Install the Solaris operating environment softwareInstall the second data CD Completing the Recovery ProcessTo Access the Terminal Concentrator from a Laptop Laptop Settings to Access Monitor ModeBits per second Data bits Parity None Flow Control None Appendix a Laptop Settings to Access Monitor Mode Cluster Platform 4500/3 User’s Guide July Ok boot net install SUNW,hme2 No response from Ethernet network Link down Creating Solaris disk label Vtoc Creating / c0t2d0s3 Management Server MStest01 192.153.47.38 at 8020c21b3c Sparc 4.2.1,REV=1999.12.09.15.37 Code Example B-2Solstice DiskSuite Configuration Checking ufs filesystems /dev/rdsk/c0t2d0s7 is clean Code Example B-2Solstice DiskSuite Configuration Code Example B-2Solstice DiskSuite Configuration Code Example B-2Solstice DiskSuite Configuration Cluster Platform 4500/3 User’s Guide July Page Cluster Platform 4500/3 User’s Guide July Connections Within the Cluster Platform 4500/3 Table C-1Boot Disk to Server ConnectionsTable C-2Disk Array to Hub Connections Table C-6Node to Node Connections Table C-8Ethernet Hub Connections Conﬁguring the Terminal Concentrator Troubleshooting the Cluster Platform 4500/3 InstallationCluster Platform 4500/3 User’s Guide July