Sun Microsystems CP32x0 manual Figures

Page 7

Figures

FIGURE 1-1

Netra CP32x0 ARTM-HD Components

1–5

FIGURE 1-2

Relationship of the Blade Server, ATCA Midplane, and ARTM-HD 1–6

FIGURE 1-3

Connecting to an External Disk Array

1–9

 

FIGURE 1-4

Connecting to Another ARTM

1–10

 

 

FIGURE 1-5

LEDs 1–11

 

 

 

 

 

FIGURE 1-6

ARTM-HD Identification Labels

1–13

 

 

FIGURE 2-1

Installing the Blade Server and ARTM-HD Into the ATCA Shelf 2–3

FIGURE 2-2

Injector/Ejector Latch and Locking Screw

2–5

FIGURE 2-3

Holding the ARTM-HD During Installation

2–6

FIGURE 2-4

Inserting the ARTM-HD

2–7

 

 

 

FIGURE 2-5

Removing the ARTM-HD

2–10

 

 

FIGURE 2-6

Jumper setting for red OOS LED (P1/P2)

2–12

FIGURE 2-7

Jumper setting for amber OOS LED (P2/P3) 2–13

FIGURE 4-1

Netra CP32x0 ARTM-HD Connectors

4–4

FIGURE 4-2

Ethernet RJ-45 Connector

4–5

 

 

FIGURE 4-3

Serial Port Connector

4–6

 

 

 

FIGURE 4-4

SAS Connectors 4–7

 

 

 

 

 

FIGURE 4-5

Zone 3 Connectors 4–8

 

 

 

 

vii

Image 7
Contents Sun Microsystems, Inc Please Recycle Contents Disk Management 3-1 3.1 RAID Support Index Index-1 Page Figures Page Tables Page How This Document Is Organized PrefaceShell Prompts Using Unix CommandsTypographic Conventions Related Documentation Third-Party Web Sites Documentation, Support, and TrainingSun Welcomes Your Comments Page Overview Features of the ARTM-HD Airflow Cooling Requirements Picmg Standards CompliancePressure Drop Rates 1Netra CP32x0 ARTM-HD Components ARTM-HD Component DiagramI/O Interfaces 3Netra CP32x0 ARTM-HD I/O Configurations Hard Disk Drive Controller Hard Disk Drives3Connecting to an External Disk Array External SAS ConnectorsLEDs 4Connecting to Another ArtmLEDs Software SupportPage Part number label Serial number label Part Number, Serial Number, and FC Address LabelsPage Installation and Service ARTM-HD About Installing and Removing1Installing the Blade Server and ARTM-HD Into the Atca Shelf Installing the ARTM-HD Retention screw Injector/ejector latch 3Holding the ARTM-HD During Installation 4Inserting the ARTM-HD Power on the system, if necessary Removing the ARTM-HD 5Removing the ARTM-HD Removing a Hard Disk Drive Installing a Hard Disk DriveChanging the OOS LED Color 6Jumper setting for red OOS LED P1/P2Reinstall the ARTM-HD Page Disk Management RAID Support SAS Bios OverviewStarting the SAS Bios Configuration Utility Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 1E Volume Viewing RAID Volume Properties Activating an Array Synchronizing an ArrayLocating a Disk Drive Deleting an ArrayPage Specifications and Connectors Physical Dimensions Specifications for the ARTM-HDEthernet Management Port Hardware Descriptions1shows the location of the connectors Connectors and Pin Assignments1 I/O Connectors Serial Port SAS Connectors Zone 3 Connectors 4lists the Zone 3, J31 connector pinouts 6lists the Zone 3, J33 connector pinouts Index Bios SAS RAID