Sun Microsystems Sun Quad manual Emc

Page 5

Declaration of Conformity

Compliance ID: QFEPCI

Product Name: SUN QFE PCI

This product has been tested and complies with the following EMC and Safety standards:

EMC

EC — Europe

This equipment complies with the following requirements of the EMC Directive 89/336/EEC:

EN55022 / CISPR22 (1985)		Class A
EN50082-1	IEC801-2 (1991)	4 kV (direct), 8 kV (air)
	IEC801-3 (1984)	3 V/m
	IEC801-4 (1988)	1.0 kV power lines, 0.5 kV signal lines
EN61000-3-2/IEC1000-3-2 (1994)		Pass

Safety

This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:

•EN60950/IEC950 (1993)

Supplementary Information

This product was tested and complies with all the requirements for the CE Mark when connected to a Sun workstation or server.

/ S /				/ S /
Dennis P. Symanski		Date		John Shades		Date
Manager, Product Compliance				Manager, Quality Assurance
Sun Microsystems Computer Company				Sun Microsystems Limited
2550 Garcia Avenue, M/S UMPK15-102				Springfield, Linlithgow
Mt. View, CA 94043, USA				West Lothian, EH49 7LR
Tel: 415-786-3255				Scotland, United Kingdom
Fax: 415-786-3723				Tel: 0506 670000
				Fax: 0506 760011

Declaration of Conformity

v

Image 5

Contents Sun Quad FastEthernet PCI Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements DOC Class a Notice Avis DOC, Classe a EMC Page Contents Specifications Running Diagnostics Tests Page How This Book Is Organized PrefaceRelated Documents Unix CommandsShell Prompts Typographic ConventionsTable P-1SunExpress Contact Information Ordering Sun DocumentsSun Welcomes Your Comments 1Sun Quad FastEthernet PCI adapter Product Overview2Sun Quad FastEthernet PCI adapter Back Panel FeaturesDisplaying the OpenBoot Prom Revision Level Checking the OpenBoot Prom Revision LevelHardware and Software Requirements 1Hardware and Software RequirementsPage Using a text editor, add the following line to the end Installing the AdapterInstalling the Adapter Ok show-devs Verifying the InstallationExamining Network Activity Perform a reconfiguration boot on the system Rebooting the SystemPage Configuring the Host Files Configuring the Driver SoftwareInstalling the Driver Software Etc/hosts file # cat /etc/hosts Reboot your systemAt the ok prompt type Booting From the NetworkConfiguring Driver Parameters Post-Installation Procedures OptionalIncreasing TCP/IP Performance As superuser root, typeType Forcing Network Speed Between 10 Mbps and 100 MbpsAuto-Negotiation Local-mac-address Property Table A-1Physical Dimensions SpecificationsPhysical Dimensions Performance Specifications Power RequirementsTable A-2Power Requirements Table A-3Performance SpecificationsEthernet channels Interface SignalsPage Internal Transceiver Configuring the Quad FastEthernet Device Driver ParametersQfe Driver Parameter, Status, and Descriptions Driver Parameter Values and DefinitionsInter-Packet Gap Parameters Defining the Current StatusTable B-1qfe Driver Parameter, Status, and Descriptions Table B-2Read-Only Parameters Defining the Current StatusIpg1 = 8 default at initialization Table B-4Parameters Defining lancemode and ipg0 Operational Mode ParametersTable B-5Operational Mode Parameters Reporting Transceiver Capabilities Defining the Number of Back-to-Back Packets to TransmitTable B-6Back-to-back Packet Transmission Capability Table B-7Read-Only Transceiver CapabilitiesTable B-8Read-Only Link Partner Capabilities Reporting the Link Partner CapabilitiesSetting Parameters Using the ndd Utility Setting qfe Driver ParametersUse the instance number to select the device To Specify the Device Instance for the ndd UtilityTo modify a parameter value, use the -setoption Using the ndd Utility in Non-Interactive Mode# ndd /dev/qfe \? Setting Forced Mode Table B-9Setting Variables in the /etc/system File Setting Parameters in the /etc/system FileSetting the ipg1 and ipg2 Parameters Setting Parameters Using the qfe.conf FileEtc/pathtoinst file Setting ipg Driver Parameters Using a qfe.conf FileKernel/drv/qfe.conf file Set the ipg1 and ipg2 parameters for the above four devicesUsing the OpenBoot Prom FCode Selftest Running Diagnostics TestsReset the system Running the Ethernet FCode Selftest DiagnosticShut down the system Type show-devsto display the list of devicesOk setenv diag-switch? false Reset and reboot the system Set the auto-boot?configuration parameter to trueEditing IndexEditing, 11 example Creating, 12 editing, 11 examplesLEDs Watch-net-all output Page Ordering Sun Documents AIR Mail PAR Avion