Sun Microsystems Sun Quad manual Running Diagnostics Tests, Using the OpenBoot Prom FCode Selftest

Page 53

A P P E N D I X D

Running Diagnostics Tests

This appendix describes how to test the Sun Quad FastEthernet PCI adapter with its FCode PROM selftest.

Note –To test the Sun Quad FastEthernet PCI adapter further, refer to the SunVTS User’s Guide that shipped with your operating system.

Using the OpenBoot PROM FCode

Selftest

The following tests are available to help identify problems with the Sun Quad FastEthernet PCI adapter if the system does not boot.

You can invoke the FCode selftest diagnostics by using the OpenBoot user interface test or test-allcommands. If you encounter an error while running diagnostics, appropriate messages will be displayed. Refer to the OpenBoot 3.x Command Reference Manual for more information on the test and test-allcommands.

The selftest exercises most functionality sub-section by sub-section and ensures the following:

■Isolates faulty field replaceable units (FRUs)

■Checks, with a high confidence, that no hardware fault exists on No Trouble Found (NTF)

■Checks connectivity during adapter card installation

■Verifies that all components are functional

39

Image 53

Contents Sun Quad FastEthernet PCI Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements DOC Class a Notice Avis DOC, Classe a EMC Page Contents Specifications Running Diagnostics Tests Page How This Book Is Organized PrefaceRelated Documents Unix CommandsShell Prompts Typographic ConventionsTable P-1SunExpress Contact Information Ordering Sun DocumentsSun Welcomes Your Comments 1Sun Quad FastEthernet PCI adapter Product Overview2Sun Quad FastEthernet PCI adapter Back Panel FeaturesDisplaying the OpenBoot Prom Revision Level Checking the OpenBoot Prom Revision LevelHardware and Software Requirements 1Hardware and Software RequirementsPage Using a text editor, add the following line to the end Installing the AdapterInstalling the Adapter Ok show-devs Verifying the InstallationExamining Network Activity Perform a reconfiguration boot on the system Rebooting the SystemPage Configuring the Host Files Configuring the Driver SoftwareInstalling the Driver Software Etc/hosts file # cat /etc/hosts Reboot your systemAt the ok prompt type Booting From the NetworkConfiguring Driver Parameters Post-Installation Procedures OptionalIncreasing TCP/IP Performance As superuser root, typeType Forcing Network Speed Between 10 Mbps and 100 MbpsAuto-Negotiation Local-mac-address Property Table A-1Physical Dimensions SpecificationsPhysical Dimensions Performance Specifications Power RequirementsTable A-2Power Requirements Table A-3Performance SpecificationsEthernet channels Interface SignalsPage Internal Transceiver Configuring the Quad FastEthernet Device Driver ParametersQfe Driver Parameter, Status, and Descriptions Driver Parameter Values and DefinitionsInter-Packet Gap Parameters Defining the Current StatusTable B-1qfe Driver Parameter, Status, and Descriptions Table B-2Read-Only Parameters Defining the Current StatusIpg1 = 8 default at initialization Table B-4Parameters Defining lancemode and ipg0 Operational Mode ParametersTable B-5Operational Mode Parameters Reporting Transceiver Capabilities Defining the Number of Back-to-Back Packets to TransmitTable B-6Back-to-back Packet Transmission Capability Table B-7Read-Only Transceiver CapabilitiesTable B-8Read-Only Link Partner Capabilities Reporting the Link Partner CapabilitiesSetting Parameters Using the ndd Utility Setting qfe Driver ParametersUse the instance number to select the device To Specify the Device Instance for the ndd UtilityTo modify a parameter value, use the -setoption Using the ndd Utility in Non-Interactive Mode# ndd /dev/qfe \? Setting Forced Mode Table B-9Setting Variables in the /etc/system File Setting Parameters in the /etc/system FileSetting the ipg1 and ipg2 Parameters Setting Parameters Using the qfe.conf FileEtc/pathtoinst file Setting ipg Driver Parameters Using a qfe.conf FileKernel/drv/qfe.conf file Set the ipg1 and ipg2 parameters for the above four devicesUsing the OpenBoot Prom FCode Selftest Running Diagnostics TestsReset the system Running the Ethernet FCode Selftest DiagnosticShut down the system Type show-devsto display the list of devicesOk setenv diag-switch? false Reset and reboot the system Set the auto-boot?configuration parameter to trueEditing IndexEditing, 11 example Creating, 12 editing, 11 examplesLEDs Watch-net-all output Page Ordering Sun Documents AIR Mail PAR Avion