Sun Microsystems 806-2989-10 manual Configuring Driver Parameters

Page 45

C H A P T E R 4

Configuring Driver Parameters

This chapter describes how to configure the driver parameters used by the Sun GigaSwift Ethernet adapter. This chapter contains the following sections:

■“GigaSwift Ethernet Device Driver Parameters” on page 25

■“Setting ce Driver Parameters” on page 33

■“GigaSwift Ethernet Driver Operating Statistics” on page 39

GigaSwift Ethernet Device Driver

Parameters

The ce device driver controls the GigaSwift Ethernet devices. The ce driver is attached to the UNIX pci name property pci108e,abba for the Sun GigaSwift Ethernet adapter (108e is the vendor ID and abba is the PCI device ID).

You can manually configure the ce device driver parameters to customize each Sun GigaSwift Ethernet adapter device in your system. This section provides an overview of the capabilities of the GigaSwift Ethernet device used in the adapter, lists the available ce device driver parameters, and describes how to configure these parameters.

The Sun GigaSwift Ethernet UTP PCI adapter is capable of all the operating speeds and modes listed in “Setting the Autonegotiation Mode” on page 36. The ce device performs autonegotiation with the remote end of the link (link partner) to select a common mode of operation. The ce device also supports a forced mode of operation.

25

Image 45

Contents Sun GigaSwift Ethernet Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements FCC Class a NoticeFCC Class B Notice ICES-003 Class B Notice Avis NMB-003, Classe B ICES-003 Class a Notice Avis NMB-003, Classe aBsmi Class a Notice Page Declaration of Conformity Product NameSun GigaSwift Ethernet UTP Adapter X1150AEN550221998 / CISPR221997 Page Contents Configuring Driver Parameters Configuring VLANsSpecifications Index Diagnostic Software and Troubleshooting IssuesPage Figures Page Tables Page How This Book Is Organized PrefaceTypographic Conventions Using Unix CommandsAccessing Sun Documentation Online Shell PromptsRelated Documentation Sun Welcomes Your Comments Ordering Sun DocumentationHardware Overview Product Overview1Sun GigaSwift Ethernet UTP Adapter Sun GigaSwift Ethernet UTP AdapterProduct Features Hardware and Software RequirementsKey Protocols and Interfaces Diagnostic Support Installing the Adapter Installing the Driver SoftwareBecome superuser 1Files and Directories on the CD-ROM See -1to identify the optional packages To Install the Adapter Installing the Adapter Without Dynamic Reconfiguration1Cat-5 Twisted-Pair Cable To Verify the InstallationList the network devices on your system Ok .properties View the .properties file for a list of device propertiesTo Set the GigaSwift Ethernet Device Primary Boot Device Setting the local-mac-addressPropertyRebooting the System To Install an Adapter in a Dynamic Reconfiguration System Installing the Adapter With Dynamic ReconfigurationIf the status of the slot is not empty or disconnected, type Configure the adapter and slot Reconfigure the devices on the adapterConnect the adapter and slot Configuring the Network Host Files Network ConfigurationEtc/hostname.ce1 # cat /etc/hosts Edit the hosts in the diskless client’s root directory To Set Up a Diskless Client on a GigaSwift Ethernet NetworkNetwork Configuration Find the root directory of the client system # grep clientname /etc/bootparamsShut down and halt the client system Proceed with the Solaris operating environment installation# pkginfo grep SUNWce GigaSwift Ethernet Device Driver Parameters Configuring Driver Parameters1ce Driver Parameter, Status, and Descriptions Driver Parameter Values and DefinitionsOperational Mode Parameters Operational Mode Parameters3Read-Write Flow Control Keyword Descriptions Flow Control ParametersGigabit Forced Mode Parameter 4Forced Mode ParameterInterpacket Gap Parameters 5Parameters Defining enableipg0 and ipg0 5defines the enableipg0 and ipg0 parametersRandom Early Drop Parameters Interrupt Parameters7RX Blanking Register for Alias Read 8RX Random Early Detecting 8-Bit Vectors9PCI Bus Interface Parameters PCI Bus Interface ParametersSetting Parameters Using the ndd Utility Setting ce Driver ParametersTo Specify Device Instances for the ndd Utility Noninteractive and Interactive ModesUse the instance number to select the device To modify a parameter value, use the -setoption Using the ndd Utility in Interactive ModeSetting the Autonegotiation Mode Setting Parameters Using the ce.conf File To Disable Autonegotiation ModeSet the advautonegcap parameter to Etc/pathtoinst file To Set Driver Parameters Using a ce.conf File10Read-Only ce Device Capabilities GigaSwift Ethernet Driver Operating Statistics11Read-Only Link Partner Capabilities Reporting the Link Partner Capabilities12Transmit and Receive Parameters Rxnewpages rxnewhdrpgs As superuser, type the netstat -kcommand To Check Link Partner SettingsPage An Overview of VLANs Configuring VLANs1shows an example network that uses VLANs Configuring VLANs 2Ethernet Tag Header Format To Configure Static VLANs# ifconfig ce123000 plumb up # ifconfig ce224000 plumb up Page Specifications ConnectorsTable A-1Cat-5 Connector Link Characteristics Physical Characteristics Performance SpecificationsPower Requirements Table A-2Performance SpecificationsSunVTS Diagnostic Software Diagnostic Software Troubleshooting IssuesRunning the Ethernet FCode Self-Test Diagnostic Using the OpenBoot Prom FCode Self- TestReset the system Shut down the systemType show-netsto display the list of devices Troubleshooting Issues Set the auto-boot?configuration parameter to trueReset and reboot the system Type the following to apply and save your changes Adv1000fdxcap Adv1000hdxcap AdvpauseTX AdvpauseRX Index Symbols