Sun Microsystems 806-2989-10 manual Declaration of Conformity, EN550221998 / CISPR221997

Page 7

Declaration of Conformity

Compliance Model Number: GCC PCI

Product Name:Sun GigaSwift Ethernet UTP Adapter (X1150A)

EMC

European Union

This equipment complies with the following requirements of the EMC Directive 89/336/EEC:

EN55022:1998 / CISPR22:1997

Class A

EN550024:1998 EN61000-4-2

4 kV (Direct), 8 kV (Air)

EN61000-4-3

3

V/m

EN61000-4-4

1.0 kV Power Lines, 0.5 kV Signal Lines

EN61000-4-5

1 kV Line-Line, 2 kV Line-Gnd Power Lines

EN61000-4-6

3

V

EN61000-4-8

3

A/m

EN61000-4-11

Pass

EN61000-3-2:1995

Pass

EN61000-3-3:1995

Pass

Safety

This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:

EC Type Examination Certificates:

EN60950:1992, 2nd Edition, Amendments 1,2,3,4,11

Supplementary Information

This product was tested and complies with all the requirements for the CE Mark.

Dennis P. Symanski

DATE

Peter Arkless

DATE

Manager, Compliance Engineering

 

Quality Manager

 

Sun Microsystems, Inc.

 

Sun Microsystems Scotland, Limited

 

901 San Antonio Road, MPK15-102

 

Springfield, Linlithgow

 

Palo Alto, CA 94303-4900, USA

 

West Lothian, EH49 7LR

 

 

 

Scotland, United Kingdom

 

Tel: 650-786-3255

 

Tel: 0506-670000

 

Fax: 650-786-3723

 

Fax: 0506 760011

 

vii

Image 7
Contents Sun GigaSwift Ethernet Adapter Installation User’s Guide Please Recycle FCC Class a Notice Regulatory Compliance StatementsFCC Class B Notice ICES-003 Class B Notice Avis NMB-003, Classe B ICES-003 Class a Notice Avis NMB-003, Classe aBsmi Class a Notice Page Product NameSun GigaSwift Ethernet UTP Adapter X1150A Declaration of ConformityEN550221998 / CISPR221997 Page Contents Configuring VLANs Configuring Driver ParametersSpecifications Index Diagnostic Software and Troubleshooting IssuesPage Figures Page Tables Page How This Book Is Organized PrefaceTypographic Conventions Using Unix CommandsShell Prompts Accessing Sun Documentation OnlineRelated Documentation Sun Welcomes Your Comments Ordering Sun DocumentationHardware Overview Product Overview1Sun GigaSwift Ethernet UTP Adapter Sun GigaSwift Ethernet UTP AdapterHardware and Software Requirements Product FeaturesKey Protocols and Interfaces Diagnostic Support Installing the Driver Software Installing the AdapterBecome superuser 1Files and Directories on the CD-ROM See -1to identify the optional packages To Install the Adapter Installing the Adapter Without Dynamic Reconfiguration1Cat-5 Twisted-Pair Cable To Verify the InstallationList the network devices on your system Ok .properties View the .properties file for a list of device propertiesTo Set the GigaSwift Ethernet Device Primary Boot Device Setting the local-mac-addressPropertyRebooting the System To Install an Adapter in a Dynamic Reconfiguration System Installing the Adapter With Dynamic ReconfigurationIf the status of the slot is not empty or disconnected, type Reconfigure the devices on the adapter Configure the adapter and slotConnect the adapter and slot Configuring the Network Host Files Network ConfigurationEtc/hostname.ce1 # cat /etc/hosts Edit the hosts in the diskless client’s root directory To Set Up a Diskless Client on a GigaSwift Ethernet NetworkNetwork Configuration Find the root directory of the client system # grep clientname /etc/bootparamsShut down and halt the client system Proceed with the Solaris operating environment installation# pkginfo grep SUNWce GigaSwift Ethernet Device Driver Parameters Configuring Driver Parameters1ce Driver Parameter, Status, and Descriptions Driver Parameter Values and DefinitionsOperational Mode Parameters Operational Mode Parameters3Read-Write Flow Control Keyword Descriptions Flow Control Parameters4Forced Mode Parameter Gigabit Forced Mode ParameterInterpacket Gap Parameters 5Parameters Defining enableipg0 and ipg0 5defines the enableipg0 and ipg0 parameters8RX Random Early Detecting 8-Bit Vectors Interrupt ParametersRandom Early Drop Parameters 7RX Blanking Register for Alias Read9PCI Bus Interface Parameters PCI Bus Interface ParametersSetting Parameters Using the ndd Utility Setting ce Driver ParametersNoninteractive and Interactive Modes To Specify Device Instances for the ndd UtilityUse the instance number to select the device To modify a parameter value, use the -setoption Using the ndd Utility in Interactive ModeSetting the Autonegotiation Mode To Disable Autonegotiation Mode Setting Parameters Using the ce.conf FileSet the advautonegcap parameter to Etc/pathtoinst file To Set Driver Parameters Using a ce.conf File10Read-Only ce Device Capabilities GigaSwift Ethernet Driver Operating Statistics11Read-Only Link Partner Capabilities Reporting the Link Partner Capabilities12Transmit and Receive Parameters Rxnewpages rxnewhdrpgs As superuser, type the netstat -kcommand To Check Link Partner SettingsPage An Overview of VLANs Configuring VLANs1shows an example network that uses VLANs Configuring VLANs 2Ethernet Tag Header Format To Configure Static VLANs# ifconfig ce123000 plumb up # ifconfig ce224000 plumb up Page Connectors SpecificationsTable A-1Cat-5 Connector Link Characteristics Table A-2Performance Specifications Performance SpecificationsPhysical Characteristics Power RequirementsSunVTS Diagnostic Software Diagnostic Software Troubleshooting IssuesShut down the system Using the OpenBoot Prom FCode Self- TestRunning the Ethernet FCode Self-Test Diagnostic Reset the systemType show-netsto display the list of devices Set the auto-boot?configuration parameter to true Troubleshooting IssuesReset and reboot the system Type the following to apply and save your changes Adv1000fdxcap Adv1000hdxcap AdvpauseTX AdvpauseRX Index Symbols