Sun Microsystems 806-2989-10 manual Reporting the Link Partner Capabilities

Page 60

TABLE 4-10Read-Only ce Device Capabilities (Continued)

Parameter	Description (Local interface Capabilities)

cap_100fdx	Local interface full-duplex capability
	0	= Not 100 Mbit/sec full-duplex capable
	1	= 100 Mbit/sec full-duplex capable
cap_100hdx	Local interface half-duplex capability
	0	= Not 100 Mbit/sec half-duplex capable
	1	= 100 Mbit/sec half-duplex capable
cap_10fdx	Local interface full-duplex capability
	0	= Not 10 Mbit/sec full-duplex capable
	1	= 10 Mbit/sec full-duplex capable
cap_10hdx	Local interface half-duplex capability
	0	= Not 10 Mbit/sec half-duplex capable
	1	= 10 Mbit/sec half-duplex capable
cap_asm_pause	Local interface flow control capability
	0	= Not asymmetric pause capable
	1	= Asymmetric pause (from the local device) capable
cap_pause	Local interface flow control capability
	0	= Not Symmetric pause capable
	1	= Symmetric pause capable

Reporting the Link Partner Capabilities

TABLE 4-11describes the read-only link partner capabilities.

TABLE 4-11Read-Only Link Partner Capabilities

Parameter	Description

lp_cap_autoneg	0	= No autonegotiation
	1	= Autonegotiation
lp_cap_1000fdx	0	= No 1000 Mbit/sec full-duplex transmission
	1	= 1000 Mbit/sec full-duplex
lp_cap_1000hdx	0	= No 1000 Mbit/sec half-duplex transmission
	1	= 1000 Mbit/sec half-duplex
lp_cap_100fdx	0	= No 100 Mbit/sec full-duplex transmission
	1	= 100 Mbit/sec full-duplex
lp_cap_100hdx	0	= No 100 Mbit/sec half-duplex transmission
	1	= 1000 Mbit/sec half-duplex
lp_cap_10fdx	0	= No 10 Mbit/sec full-duplex transmission
	1	= 10 Mbit/sec full-duplex

40 Sun GigaSwift Ethernet Adapter Installation and User’s Guide • February 2001

Image 60

Contents Sun GigaSwift Ethernet Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements FCC Class a NoticeFCC Class B Notice ICES-003 Class a Notice Avis NMB-003, Classe a ICES-003 Class B Notice Avis NMB-003, Classe BBsmi Class a Notice Page Declaration of Conformity Product NameSun GigaSwift Ethernet UTP Adapter X1150AEN550221998 / CISPR221997 Page Contents Configuring Driver Parameters Configuring VLANsSpecifications Diagnostic Software and Troubleshooting Issues IndexPage Figures Page Tables Page Preface How This Book Is OrganizedUsing Unix Commands Typographic ConventionsAccessing Sun Documentation Online Shell PromptsRelated Documentation Ordering Sun Documentation Sun Welcomes Your CommentsProduct Overview Hardware OverviewSun GigaSwift Ethernet UTP Adapter 1Sun GigaSwift Ethernet UTP AdapterProduct Features Hardware and Software RequirementsKey Protocols and Interfaces Diagnostic Support Installing the Adapter Installing the Driver SoftwareBecome superuser 1Files and Directories on the CD-ROM See -1to identify the optional packages Installing the Adapter Without Dynamic Reconfiguration To Install the AdapterTo Verify the Installation 1Cat-5 Twisted-Pair CableList the network devices on your system View the .properties file for a list of device properties Ok .propertiesSetting the local-mac-addressProperty To Set the GigaSwift Ethernet Device Primary Boot DeviceRebooting the System Installing the Adapter With Dynamic Reconfiguration To Install an Adapter in a Dynamic Reconfiguration SystemIf the status of the slot is not empty or disconnected, type Configure the adapter and slot Reconfigure the devices on the adapterConnect the adapter and slot Network Configuration Configuring the Network Host FilesEtc/hostname.ce1 # cat /etc/hosts To Set Up a Diskless Client on a GigaSwift Ethernet Network Edit the hosts in the diskless client’s root directoryNetwork Configuration # grep clientname /etc/bootparams Find the root directory of the client systemProceed with the Solaris operating environment installation Shut down and halt the client system# pkginfo grep SUNWce Configuring Driver Parameters GigaSwift Ethernet Device Driver ParametersDriver Parameter Values and Definitions 1ce Driver Parameter, Status, and DescriptionsOperational Mode Parameters Operational Mode ParametersFlow Control Parameters 3Read-Write Flow Control Keyword DescriptionsGigabit Forced Mode Parameter 4Forced Mode ParameterInterpacket Gap Parameters 5defines the enableipg0 and ipg0 parameters 5Parameters Defining enableipg0 and ipg0Interrupt Parameters Random Early Drop Parameters7RX Blanking Register for Alias Read 8RX Random Early Detecting 8-Bit VectorsPCI Bus Interface Parameters 9PCI Bus Interface ParametersSetting ce Driver Parameters Setting Parameters Using the ndd UtilityTo Specify Device Instances for the ndd Utility Noninteractive and Interactive ModesUse the instance number to select the device Using the ndd Utility in Interactive Mode To modify a parameter value, use the -setoptionSetting the Autonegotiation Mode Setting Parameters Using the ce.conf File To Disable Autonegotiation ModeSet the advautonegcap parameter to To Set Driver Parameters Using a ce.conf File Etc/pathtoinst fileGigaSwift Ethernet Driver Operating Statistics 10Read-Only ce Device CapabilitiesReporting the Link Partner Capabilities 11Read-Only Link Partner Capabilities12Transmit and Receive Parameters Rxnewpages rxnewhdrpgs To Check Link Partner Settings As superuser, type the netstat -kcommandPage Configuring VLANs An Overview of VLANs1shows an example network that uses VLANs Configuring VLANs To Configure Static VLANs 2Ethernet Tag Header Format# ifconfig ce123000 plumb up # ifconfig ce224000 plumb up Page Specifications ConnectorsTable A-1Cat-5 Connector Link Characteristics Performance Specifications Physical CharacteristicsPower Requirements Table A-2Performance SpecificationsDiagnostic Software Troubleshooting Issues SunVTS Diagnostic SoftwareUsing the OpenBoot Prom FCode Self- Test Running the Ethernet FCode Self-Test DiagnosticReset the system Shut down the systemType show-netsto display the list of devices Troubleshooting Issues Set the auto-boot?configuration parameter to trueReset and reboot the system Type the following to apply and save your changes Adv1000fdxcap Adv1000hdxcap AdvpauseTX AdvpauseRX Symbols Index