Network Technologies 900GV manual Fru Led

Page 23

Module Components

Item

Icon

Name

Description

 

 

 

 

 

 

5

 

 

 

Load/Dump/

Indicates the link status of the Load/

 

 

 

 

Management(LDM)

Dump/Management port.

 

 

 

 

Port Status LED

 

6

 

 

 

LDM Activity LED

Indicates when the LDM port is

 

 

 

 

 

transmitting or receiving packets.

7

 

 

 

LDM Port

Dedicated 10BaseT Ethernet port.

 

 

 

 

 

Supports upline dump. (A dump entry

 

 

 

 

 

must be set up in config_acct in order

 

 

 

 

 

for the dump to occur.) This port is

 

 

 

 

 

wired as a straight-through connector.

8

 

 

 

Reset/Dump Button

Used to either reset the module or

 

 

 

 

 

perform an upline dump, followed by

a reset. (A dump entry must be set up in config_acct in order for the dump to occur.) If this button is pressed as operational code initializes, the module will reset to current settings. If the module is in operation mode, hold the button for five seconds. Use a non-conductive device to press the button.

9

Port Activity LED

10

Port Status LED

11

FRU LED

12

MMI port for

 

Gigabit Ethernet

 

connectors

Indicates network traffic level.

Shows the status of the ports. Indicates if the port is enabled or disabled and receiving a valid link.

Indicates the GBIC is a Field Replacable Unit (FRU).

Support for Gigabit Ethernet Multi- Mode Fiber (MMF), Gigabit Ethernet Single-Mode Fiber (SMF). The GBIC connectors are color coded: black for shortwave and blue for longwave.

1The VNbus Status and Traffic LEDs display different indications during a load state. Refer to the release notes for current descriptions.

Installing the DIGITAL VNswitch 900GV 2-3

Image 23
Contents Revision Information Digital VNswitch 900GV Installation and ConfigurationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Intended Audience PrefaceOverview Purpose of the ManualSection Description OrganizationTitle and Order Description Associated DocumentsBoldface ConventionsConvention Description Documentation Comments Accessing Online InformationOnline Services Page Achtung SafetyThis action deletes all configured settings and replaces Topic Chapter Product IntroductionThis Chapter What is the Digital VNswitch 900GV? Hot Swap FeaturesConfiguration and Management Ethernet BridgingMibs Vlan Secure Domains Introduction Chapter Installing the Digital VNswitch 900GVIcon Name Description Front Panel LEDs and ConnectorsModule Components Front Panel ComponentsFRU LED Name Description Back Panel ComponentsBack Panel Components Task 1 Compare the Power Ratings How to Install the ModuleStep Action Task 2 Seat the ModuleStage Description Task 3 Verify Initial LED OperationIf… Then… 5LDM Port Cable Connection Task 4 Connect the LDM Port Cable6GBIC Connection Task 5 Connect the Gbic ConnectorFiber Size Fiber Bandwidth Distance Task 6 Connect the Duplex SC CablesLong Wave Length Blue HP 5611 Chapter Installing the Setup Port Cable If the setup port device is… Use this cable… Setup Port Signaling StandardsSetup Port Device Cabling Item Description Connecting to the Setup Port1Setup Port Cabling Components Chapter Configuring the Module in a Digital MultiSwitchAssigning an IP Address Redirect Mode Digital MultiSwitch 900 Installation MenuStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration Configure IPTopic SET Smnp READ/WRITE Community Set Snmp Read/Write CommunityADD Snmp Trap Addresses Add Snmp Trap AddressesLine Field Description Delete Snmp Trap Addresses Delete Snmp Trap AddressesSet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSet Out-of-Band Interface IP Address OUT-OF-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Options from the VNswitch 900GV Installation Menu Product-Specific Options VNswitch 900GVPRODUCT-SPECIFIC Options Product-Specific Options MultiSwitchPage Removing the Cables, Connector and Module 1Removing the LDM Port Cable Removing the CablesGbic Removal Removing the Gbic Card3Unseating the Module Unseating the ModuleThis Appendix Appendix a Problem SolvingEvent Description Normal Power-UpOff On Green On Yellow Flashing LED DescriptionsTable A-1Module LED States LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Appendix B Connector Pin Assignments and Adapters 10BaseT Port 8-pin MJ Straight-through Connector Connectors and Pin AssignmentsH8571-J Adapter AdaptersFigure B-3 H8575-A Adapter H8575-A AdapterAppendix C Product Specifications Table C-1 Product Specifications Parameter Product SpecificationsTable C-3German Acoustical Specifications Acoustical SpecificationsTable C-2Acoustical Specifications Table C-4 Connectors Quantity Connectors

900GV specifications

Network Technologies 900GV is an advanced networking solution designed to meet the demands of today's high-performance environments. As organizations increasingly rely on seamless connectivity and robust data transmission, the 900GV stands out due to its exceptional capabilities. One of its key features is its ability to deliver high-speed data transfer across extensive distances, making it an ideal choice for both enterprise and industrial applications.

The 900GV harnesses advanced wireless technology, allowing for reliable communication without the constraints of wired connections. This flexibility enables organizations to deploy their networks in challenging geographical locations or areas where prolonged cabling might be impractical. The device is particularly noted for utilizing a proprietary modulation scheme, which enhances data throughput while minimizing latency. This is especially vital for businesses that require real-time data exchange, such as financial institutions or large-scale manufacturing operations.

Another distinctive aspect of the 900GV is its built-in redundancy mechanisms. With dual power inputs and failover capabilities, the device ensures that network connectivity remains uninterrupted even in adverse conditions. This reliability is vital for mission-critical environments where downtime can result in significant losses or operational disruptions. The 900GV also features advanced security protocols, including encryption options that safeguard data against unauthorized access, thereby instilling confidence in users regarding the safety of their networks.

Moreover, the Network Technologies 900GV is compatible with various networking standards, making it an incredibly versatile solution. It supports various protocols, including Ethernet and IP, which further enhances its integration capabilities within existing network architectures. The device is designed with user-friendly diagnostics tools that simplify network management and monitoring, allowing IT teams to address potential issues proactively.

In conclusion, Network Technologies 900GV is a premier networking solution that combines high-speed data transfer, reliable connectivity, and robust security features. Its adaptability to various environments and protocols makes it essential for organizations looking to enhance their network infrastructure. With its state-of-the-art technology and comprehensive characteristics, the 900GV is poised to meet the evolving demands of modern networking and communication.