Network Technologies 900GV manual How to Install the Module, Task 1 Compare the Power Ratings

Page 25

How to Install the Module

How to Install the Module

The hot-swap feature allows you to install the module into the DIGITAL MultiSwitch 900 without turning off power. Seating the module initiates the power-up.

To install the module, complete the following tasks.

Task 1: Compare the Power Ratings

Compare your module’s power requirements (1) with the values shown in the Chassis Manager (2) status display (Figure 2-3).

If any of the module’s power requirements exceed the values shown in the status display, add another power supply (see the DIGITAL MultiSwitch 900 Owner’s Manual).

Figure 2-3:Sample Power Ratings

1

2

	41.0W
	6.70 A	5	V	Available: 90.5 W
	0.12 A	12	V
				5V: 13.0 A, 15V: 3.5 A
	0.50 A	15	V

NPB-1048-98F

Installing the DIGITAL VNswitch 900GV 2-5

Image 25

Contents

Revision Information Digital VNswitch 900GV Installation and ConfigurationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Overview PrefacePurpose of the Manual Intended AudienceSection Description OrganizationTitle and Order Description Associated DocumentsConvention Description ConventionsBoldface Online Services Accessing Online InformationDocumentation Comments Page Achtung SafetyThis action deletes all configured settings and replaces This Chapter Chapter Product IntroductionTopic What is the Digital VNswitch 900GV? Configuration and Management FeaturesHot Swap Ethernet BridgingMibs Vlan Secure Domains Introduction Chapter Installing the Digital VNswitch 900GVModule Components Front Panel LEDs and ConnectorsFront Panel Components Icon Name DescriptionFRU LED Back Panel Components Back Panel ComponentsName Description Task 1 Compare the Power Ratings How to Install the ModuleStep Action Task 2 Seat the ModuleIf… Then… Task 3 Verify Initial LED OperationStage Description 5LDM Port Cable Connection Task 4 Connect the LDM Port Cable6GBIC Connection Task 5 Connect the Gbic ConnectorLong Wave Length Blue HP 5611 Task 6 Connect the Duplex SC CablesFiber Size Fiber Bandwidth Distance Chapter Installing the Setup Port Cable Setup Port Device Cabling Setup Port Signaling StandardsIf the setup port device is… Use this cable… Item Description Connecting to the Setup Port1Setup Port Cabling Components Chapter Configuring the Module in a Digital MultiSwitchAssigning an IP Address Redirect Mode Digital MultiSwitch 900 Installation MenuStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration Configure IPTopic SET Smnp READ/WRITE Community Set Snmp Read/Write CommunityLine Field Description Add Snmp Trap AddressesADD Snmp Trap Addresses Delete Snmp Trap Addresses Delete Snmp Trap AddressesSet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSet Out-of-Band Interface IP Address OUT-OF-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Options from the VNswitch 900GV Installation Menu Product-Specific Options VNswitch 900GVPRODUCT-SPECIFIC Options Product-Specific Options MultiSwitchPage Removing the Cables, Connector and Module 1Removing the LDM Port Cable Removing the CablesGbic Removal Removing the Gbic Card3Unseating the Module Unseating the ModuleThis Appendix Appendix a Problem SolvingEvent Description Normal Power-UpTable A-1Module LED States LED DescriptionsOff On Green On Yellow Flashing LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Appendix B Connector Pin Assignments and Adapters 10BaseT Port 8-pin MJ Straight-through Connector Connectors and Pin AssignmentsH8571-J Adapter AdaptersFigure B-3 H8575-A Adapter H8575-A AdapterAppendix C Product Specifications Table C-1 Product Specifications Parameter Product SpecificationsTable C-2Acoustical Specifications Acoustical SpecificationsTable C-3German Acoustical Specifications Table C-4 Connectors Quantity Connectors