Network Technologies 900GV manual Connecting to the Setup Port, Item Description

Page 33

Connecting to the Setup Port

Connecting to the Setup Port

To connect to the setup port on the module, complete the following steps:

Step Action

1Ensure that the transmit and receive baud rates on the setup port device are set to 9600 baud, 8-bits, no parity.

2Connect the setup port device to the setup port connector on the DIGITAL MultiSwitch 900.

The following legend identifies the setup port cabling in Figure 3-1:

Item Description

1Out-of-Band Management (OBM) Port

2Setup Port

3Setup Port Cable

4Setup Port Device

Installing the Setup Port Cable 3-3

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
Revision Information Digital VNswitch 900GV Installation and ConfigurationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Overview PrefacePurpose of the Manual Intended AudienceSection Description OrganizationTitle and Order Description Associated DocumentsConventions Convention DescriptionBoldface Accessing Online Information Online ServicesDocumentation Comments Page Achtung SafetyThis action deletes all configured settings and replaces Chapter Product Introduction This ChapterTopic What is the Digital VNswitch 900GV? Features Configuration and ManagementHot Swap Ethernet BridgingMibs Vlan Secure Domains Introduction Chapter Installing the Digital VNswitch 900GVModule Components Front Panel LEDs and ConnectorsFront Panel Components Icon Name DescriptionFRU LED Back Panel Components Back Panel ComponentsName Description Task 1 Compare the Power Ratings How to Install the ModuleStep Action Task 2 Seat the ModuleTask 3 Verify Initial LED Operation If… Then…Stage Description 5LDM Port Cable Connection Task 4 Connect the LDM Port Cable 6GBIC Connection Task 5 Connect the Gbic ConnectorTask 6 Connect the Duplex SC Cables Long Wave Length Blue HP 5611Fiber Size Fiber Bandwidth Distance Chapter Installing the Setup Port Cable Setup Port Signaling Standards Setup Port Device CablingIf the setup port device is… Use this cable… Item Description Connecting to the Setup Port1Setup Port Cabling Components Chapter Configuring the Module in a Digital MultiSwitchAssigning an IP Address Redirect Mode Digital MultiSwitch 900 Installation MenuStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration Configure IPTopic SET Smnp READ/WRITE Community Set Snmp Read/Write CommunityAdd Snmp Trap Addresses Line Field DescriptionADD Snmp Trap Addresses Delete Snmp Trap Addresses Delete Snmp Trap AddressesSet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSet Out-of-Band Interface IP Address OUT-OF-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Options from the VNswitch 900GV Installation Menu Product-Specific Options VNswitch 900GVPRODUCT-SPECIFIC Options Product-Specific Options MultiSwitchPage Removing the Cables, Connector and Module 1Removing the LDM Port Cable Removing the CablesGbic Removal Removing the Gbic Card3Unseating the Module Unseating the ModuleThis Appendix Appendix a Problem SolvingEvent Description Normal Power-UpLED Descriptions Table A-1Module LED StatesOff On Green On Yellow Flashing LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Appendix B Connector Pin Assignments and Adapters 10BaseT Port 8-pin MJ Straight-through Connector Connectors and Pin AssignmentsH8571-J Adapter AdaptersFigure B-3 H8575-A Adapter H8575-A AdapterAppendix C Product Specifications Table C-1 Product Specifications Parameter Product SpecificationsAcoustical Specifications Table C-2Acoustical SpecificationsTable C-3German Acoustical Specifications Table C-4 Connectors Quantity Connectors
Top Page Image Contents