Network Technologies 900GV Task 6 Connect the Duplex SC Cables, Long Wave Length Blue HP 5611

Page 30

How to Install the Module

Task 6: Connect the Duplex SC Cables

The DIGITAL VNswitch 900GV uses both Single-Mode Fiber (SMF) and Multi- Mode Fiber (MMF) port connectors.

WARNING

Some fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume the cable is connected to a light source.

Table 2-3and Table 2-4describe supported Short Wave Length and Long Wave Length cable distances.

Table 2-3:Short Wave Length - Black (HP 5601 - 850)

Fiber Size		Fiber Bandwidth	Distance

62.5	Microns (MMF):	160MHz per Kilometer	2 to 220 Meters
		200MHz per Kilometer	2 to 275 Meters
50.0	Microns (MMF)	400MHz per Kilometer	2 to 250 Meters

Table	2-4:Long Wave Length - Blue (HP 5611 - 1300)

Fiber Size		Fiber Bandwidth	Distance

62.5	Microns (MMF)	500MHz per Kilometer	2 to 550 Meters*
50.0	Microns (MMF)	400MHz per Kilometer	2 to 550 Meters*
10.0	Microns (SMF)		2 to 5,000 Meters

*requires offset launch fiber jumper MMF indicates Multi Mode Fiber SMF indicates Single Mode Fiber

2-10 Installing the DIGITAL VNswitch 900GV

Image 30

Contents

Digital VNswitch 900GV Installation and Configuration Revision InformationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Purpose of the Manual PrefaceOverview Intended AudienceOrganization Section DescriptionAssociated Documents Title and Order DescriptionConventions Convention DescriptionBoldface Accessing Online Information Online ServicesDocumentation Comments Page Safety AchtungThis action deletes all configured settings and replaces Chapter Product Introduction This ChapterTopic What is the Digital VNswitch 900GV? Features Configuration and ManagementHot Swap Bridging EthernetMibs Vlan Secure Domains Chapter Installing the Digital VNswitch 900GV IntroductionFront Panel Components Front Panel LEDs and ConnectorsModule Components Icon Name DescriptionFRU LED Back Panel Components Back Panel ComponentsName Description How to Install the Module Task 1 Compare the Power Ratings Task 2 Seat the Module Step ActionTask 3 Verify Initial LED Operation If… Then…Stage Description Task 4 Connect the LDM Port Cable 5LDM Port Cable ConnectionTask 5 Connect the Gbic Connector 6GBIC ConnectionTask 6 Connect the Duplex SC Cables Long Wave Length Blue HP 5611Fiber Size Fiber Bandwidth Distance Chapter Installing the Setup Port Cable Setup Port Signaling Standards Setup Port Device CablingIf the setup port device is… Use this cable… Connecting to the Setup Port Item Description1Setup Port Cabling Components Configuring the Module in a Digital MultiSwitch ChapterAssigning an IP Address Digital MultiSwitch 900 Installation Menu Redirect ModeStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings Configure IP IP ConfigurationTopic Set Snmp Read/Write Community SET Smnp READ/WRITE CommunityAdd Snmp Trap Addresses Line Field DescriptionADD Snmp Trap Addresses Delete Snmp Trap Addresses Delete Snmp Trap AddressesIN-BAND Interface IP Address Configuration Set In-Band Interface IP AddressOUT-OF-BAND Interface IP Address Configuration Set Out-of-Band Interface IP AddressSet Default Gateway SET IN-BAND Interface Default Gateway AddressGo to Local Console Product-Specific Options VNswitch 900GV Options from the VNswitch 900GV Installation MenuProduct-Specific Options MultiSwitch PRODUCT-SPECIFIC OptionsPage Removing the Cables, Connector and Module Removing the Cables 1Removing the LDM Port CableRemoving the Gbic Card Gbic RemovalUnseating the Module 3Unseating the ModuleAppendix a Problem Solving This AppendixNormal Power-Up Event DescriptionLED Descriptions Table A-1Module LED StatesOff On Green On Yellow Flashing LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Appendix B Connector Pin Assignments and Adapters Connectors and Pin Assignments 10BaseT Port 8-pin MJ Straight-through ConnectorAdapters H8571-J AdapterH8575-A Adapter Figure B-3 H8575-A AdapterAppendix C Product Specifications Product Specifications Table C-1 Product Specifications ParameterAcoustical Specifications Table C-2Acoustical SpecificationsTable C-3German Acoustical Specifications Connectors Table C-4 Connectors Quantity