Sun Microsystems installation manual SPARCserver 2000E Power Supply Installation Manual-April

Page 4

A.1 Removal Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 A.1.1 Opening the Hinged Door . . . . . . . . . . . . . . . . . . . . . A-1 A.1.2 Removing the Vented Front Panels. . . . . . . . . . . . . . A-2 A.1.3 Removing the Side Panels . . . . . . . . . . . . . . . . . . . . . A-3 A.1.4 Removing the EMI Shield . . . . . . . . . . . . . . . . . . . . . A-4 A.1.5 Rear Screen Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

A.2 Closing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

A.2.1 EMI Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

A.2.2 Rear Screen Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

A.2.3 Vented Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7

A.2.4 Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7

iv	SPARCserver 2000E Power Supply Installation Manual—April 1995

Image 4

Contents SPARCcenter 2000E Power Supply Installation Manual Trademarks Contents SPARCserver 2000E Power Supply Installation Manual-April Figures SPARCserver 2000E Power Supply Installation Manual-April Tables Viii Preface Power Supply Installation, explains how to performHow This Book Is Organized Related Documents Application Title Part NumberShell Prompts in Command Examples What Typographic Changes MeanXii Safety Precautions Before You StartSymbols Problem PrecautionOFF Tools Required Power Supply Installation Powering Down the System Open Boot PromOperating System OnDiagnostics Secure Standby Installing the Bottom Power Supply AccessIdentifying a Redundant-Capable Cabinet Disconnect the top power supply power cord Installing the SupplyPreparation Remove the power supply cage cover panel 4Disconnecting the Top Power Supply Power CordRemove the AC Distribution Unit Remove the Breaker Box Power Supply Physical Installation Filter CablePower supply cage Screws 6 places Install the bottom cover panel Main Bus Bar InstallationTighten all nuts and screws installed in and Step Power Harness Installation 12Installing the Main Bus Bar+12V +12V Return Power harness Part Cabling Plug in the filter cablePlace the breaker box against power supply cage 16Replacing the Power Breaker Box17Connecting the Power Cords Power Supply Sense Cable Plug it into J1 near the top of the supplyRestore the System 19Replacing the Power Supply Compartment EMI PanelTurn the key switch to Power-on position. See Figure Restarting the SystemRemote Local Watch the terminal screen for any Post error messages Reading Boot Messages 21System Reset SwitchDC power green Fault yellow System running green Bottom Top Power Supply SPARCserver 2000E Power Supply Installation Manual-April Removal Procedures AccessOpening the Hinged Door Removing the Vented Front Panels 1Opening the Hinged DoorRemoving the Side Panels 2Removing the Vented Front PanelsRemoving the EMI Shield 3Removing the Side PanelsRear Screen Panel 4Removing the EMI ShieldClosing the System EMI PanelVented Front Panel Side PanelsSPARCserver 2000E Power Supply Installation Manual-April Revision History SPARCserver 2000E Power Supply Installation Manual-April Reader Comments Business Reply Mail