Paradyne 8540, 8546 manual Ports Options 2, DSL Ports DSL Parameters

Page 47

RADSL Card Configuration

Table 3-2. Ports Options (2 of 3)

DSL Ports (DSL Parameters)

A-B-B

 

 

Allows configuration of the operational and alarm parameters of the DSL ports. Each DSL port is configured separately.

Action – Edit to configure the DSL ports. Reset the port to make changes active.

Port # – Enter port 1 to 4 (Default = 0).

RTU Type – Model number of the service node. For Model 8540, selections are 5246/5216 (Default = 5216). For Model 8546, selections are 5446r1/5446r2 (Default = 5446r2). (This field is read-only.)

Port Desc – Enter port description, such as user name, etc. (40 characters maximum).

Tx Power – 0 dB, –3 dB, –6 dB. For the RADSL card. Enter the rate that allows you to reduce the transmit power by: –3 dB or –6 dB (Default = 0 dB). Short loops require less power, reducing crosstalk and giving better performance on longer loops in the same cable bundle.

RTU Tx Power – 0 dB, –3 dB, –6 dB, –9dB. From the RTU. Enter the rate that allows you to reduce the transmit power by: –3 dB or –6 dB (Default = –6 dB).

Startup Margin – The Startup Margin (SM) field is used to determine the quality of the connection of the upstream link on system startup. It is used in conjunction with the adaptive speed fields to determine the initial line speeds of the DSL link. The value is between –3 and 9. In Adaptive Mode, if the margin falls below SM, the DSL link will be restarted at a slower speed. If the calculated margin of the next speed is greater than SM by 3 dB, the speed will increase. Enter –3 to 9 (Default = 3).

Reed-Solomon Interleaving – Long/Short (Default = Long).

Behavior – Fixed/Adaptive (Default = Adaptive). In fixed rate mode, the DSL port will operate at the specified upstream and downstream speed. In rate adaptive mode, the rates will not exceed the maximum speed and traps are sent when the links drop below the minimum, as the transmission characteristics of the loop change.

Fixed: Dn Speed* – 7168/6272/5120/4480/3200/2688/2560/2240/1920/1600/1280/ 1024/960/896/768/640/512/384/256 (Default = 2560 kbps).

Fixed: Up Speed* – 1088/952/816/680/544/476/408/340/272/204/136/119/102/90.6/85/68/51/45.3/34/11.3 (Default = 1088 kbps). Enter the fixed upstream speed.

Adaptive: Max Dn Speed* – 7168/6272/5120/4480/3200/2688/2560/2240/1920/1600/ 1280/1024/960/896/768/640/512/384/256 (Default = 7168 kbps). Enter the maximum downstream speed.

*If you select a downstream speed of 2560 or higher, your upstream speed selection is limited to 1088/952/680/408 kbps.

8000-A2-GB20-50

April 2000

3-13

Page 46 Page 48
Image 47
Page 46 Page 48
Contents HOTWIREr 8540 and 8546 Radsl Cards Copyright E 2000 Paradyne Corporation All rights reserved Contents Radsl Card Configuration Glossary Index Contents Document Purpose and Intended Audience About This GuideProduct-Related Documents Document SummaryVii Viii What is the Hotwire DSL System? Hotwire DSL System DescriptionOptional Central Office CO Customer Premises CPInput Hotwire DSL ChassisApril DSL Card MCP Card Front View of a Hotwire 8820 GranDSLAM ChassisRadsl Cards Use this MCC Card This Hotwire ChassisMCC Card Software Functionality FeaturesLevels of Access Monitoring the DSL Cards Configuring the DSL CardsTroubleshooting and Diagnostics Hotwire DSL System Description Menu and Screen Formats Hotwire Menus and ScreensComponents of a Hotwire Menu Luserlogin or Ruserlogin where L indicates a local login Components of a Hotwire ScreenKeys Definition Commonly Used Navigation KeysCommunications Controller MCC Card User’s Guide User Login Screen Hotwire Chassis Hotwire Menu HierarchyHotwire Chassis Main Menu Applications Hotwire DSL MenuHotwire DSL DiagnosticsDSL Card Configuration Menu DSL Card Monitoring Menu Logging In to the SystemCard Selection Screen R D U X X Column Position Display Description HeadingAutomatically Logging Out Accessing the Hotwire DSL MenuExiting From the System Manually Logging OutHotwire Menus and Screens Port Naming Conventions Radsl Card ConfigurationOverview For the Management Domain, perform task On the . . . See Configuring the MCC Card, DSL Cards, and RTUsFor each Service Domain See Perform task Card DCE ManagerServer 10BT DCE Manager Router MCC CardDCE Manager Router DCE Manager Server8546 ISP Router8540 DSL Configuration Card Status Screens Card Info System Information DNS Setup Configure DNSCard Status Options 1 Nvram Clear Screen Clear Nvram Card Status Options 2Time/Date DOS Machine Nvram Config LoaderCard Reset Reset System Card Status Options 3Apply Download Card Status Menu Options 4Download Code Download Code and Apply Download Ethernet Port DSL Configuration Ports ScreensPorts Options 1 DSL Ports DSL Parameters Ports Options 2Thresholds for Trap Messages Ports Options 3DSL Ports DSL Parameters cont’d General Interfaces DSL Configuration Interfaces ScreensInterfaces Options 1 Control Control Interface Interfaces Options 2IP Network Link Options Echo Policy Default =Interfaces Options 3 Negotiate OptionsDSL Configuration Users Screens Users Options Users * Configure AccountDSL Configuration IP Router Screens Message Meaning Static Routes IP Router Options 1Filter Table IP Router Options 2Martian Networks Delete Rule Yes/No IP Router Filters IP Filter ConfigurationIP Router Options 3 IP Router Options 4 Management System Source Validation for Radsl Cards DSL Configuration Snmp ScreensCommunities/Traps Snmp Communities/Traps Snmp OptionsSecurity Snmp Security DSL Configuration Dhcp Relay Screens Select Configuration → Dhcp Relay → Domain Names A-G-A Configuring Dhcp Relay Agent dynamic addressingServers Dhcp Relay OptionsDomain Names Interface IP Address Read-onlyDSL Configuration RTU Screens RTU Selection RTU OptionsDSL Monitoring Menu Monitoring the Hotwire DSL SystemDSL Monitoring Card Status Screens Card Info General Card Information Login HistoryCard Status Options DSL Monitoring Physical Layer Screens Ether Statistics Ethernet Statistics Physical Layer Options 1Active List Active Ports List Hdlc Bus Stats Hdlc Bus Statistics Physical Layer Options 2DSL Link Perf DSL Link Performance Summary Physical Layer Options 3Customer Data Physical Layer Options 4DSL Perf Stats DSL Performance Stats All DataDSL Xmit Status DSL Transmit Stats DSL Error StatsPhysical Layer Options 5 DSL Monitoring Interfaces Screens Status Interface Status Monitor Interfaces OptionsActive List Active Interfaces List Monitoring → Network Protocol B-D DSL Network Protocol ScreensUDP Statistics Network Protocol Options 1Socket Statistics TCP Data Stats TCP Data Statistics Network Protocol Options 2IP Statistics Network Protocol Options 3TCP Connection Statistics Icmp Statistics Icmp Packet Statistics Network Protocol Options 4Snmp Statistics Network Protocol Options 5Hdlc Statistics Hdlc Statistics Network Protocol Options 6Ipcp General Stats PPP H C Network Protocol Options 7PPP Stats General H a LCP Stats PPP H BDSL IP Router Screens Route Information Window Routing TableRouting Table Screen ARP Table DSL Configuration RTU Screens RTU Information Applications Screens Diagnostics and TroubleshootingTraceRoute Ping IP SettingsApplications Options Diagnostic Screens Packet Echo Test Diagnostics OptionsAlarms Card Alarms SelftestNo Response at Startup TroubleshootingChecking Alarms Major Alarms 1 Failure Type ActionResponding Major Alarms 2 Failure Type ActionEthernet port 1. Check cable connections to the DSL chassis DSL portThreshold Minor Alarms 1 Failure Type ActionMargin Link Down Minor Alarms 2 Failure Type ActionError Rate Example Syslog Messages Syslog MessagesExample 3. System Status Message Network Problems 1 Action Network ProblemsInterfaces A-C Network Problems 2 ActionMonitoring the Hotwire DSL System Network Problems 3 ActionDiagnostics and Troubleshooting Download Code Scenario Two Download Only System Download CodeApply Download Fully Operational SystemSnmp Traps Setting Up Snmp Trap FeaturesDSL Snmp Community Strings and Authentication Failure Trap Enable DSL Port Traps Table B-1. DSL Card Traps 1 Event Severity Comment Trap # DSL Card TrapsSnmp Traps XDSL margin low Minor Table B-1. DSL Card Traps 4 Event Severity Comment Trap # Table B-2. Standard Traps Event Trap Class Comment RTU Related TrapsStandard Traps Enterprise-Specific TrapsSnmp Traps Hotwire 5446 RTU Setup Overview RTU SetupFigure C-1. IP Routing Table Example IP Injection Type IP Address Network Mask Next Hop RouterDownloading the IP Injection Tool Accessing the Hotwire 5446 RTU IP Injection MIBAccessing the IP Injection Tool Community String Entries Additional pdn-common MIBs Supported IP and Device MIBs SupportedConfiguration Requirements Network Management Systems From an Snmp workstation Using a MIB BrowserMIB Browser Techniques ProceduresIP Injection Tool Group Objects Table Viewable 5446 RTU ARP Table Glossary Gateway address EthernetEthernet address FilterPots splitter OpenLane DCEManager PacketUpstream TelnetTerminal emulation TraceRouteNumbers IndexIN-2
Related manuals
Manual 161 pages 59.8 Kb Manual 12 pages 4.86 Kb
Top Page Image Contents