Paradyne 8546, 8540 manual Interfaces Options 2, IP Network, Control Control Interface

Page 50

RADSL Card Configuration

Table 3-3. Interfaces Options (2 of 3)

IP Network

A-C-B

 

 

Allows you to configure up to 16 IP addresses for a port. Configure one IP address for each service domain on the DSL card.

IP Interface – Name of the interface. Enter up to 15 characters. s1b = backplane; e1a = Ethernet port; s1c, s1d, s1e, and s1f = DSL ports.

Base IP Addr – nnn.nnn.nnn.nnn format. (This field is read-only.)

Base Subnet Mask – nnn.nnn.nnn.nnn format. (This field is read-only.)

IP Addr – nnn.nnn.nnn.nnn format. (You may enter up to 16 addresses for LANs.) Only appears if e1a is the IP interface name.

Subnet Mask – nnn.nnn.nnn.nnn format. (You may enter one for each address above.) Only appears if e1a is the IP interface name.

Input Filter – Optional. (Blank to disable filtering.) Prevents unwanted packets from entering the RADSL card through a specified interface.

Output Filter – Optional. (Blank to disable filtering.) Prevents unwanted packets from going out of the RADSL card through a specified interface.

Source Routing – Directs data to the correct address. Set to enable for networks with multiple ISPs. Leave blank to disable filtering. If you disable source routing for an interface, any existing source route for that interface is removed from the active routing table. Source routing should be disabled on the e1a interface for most installations. Use care when enabling source routing on the e1a interface as it can create routing loops. (Default = Disable for e1a interface or Enable for s1x interface).

Peer IP Address – nnn.nnn.nnn.nnn format. IP address associated with the other end of the link; i.e., the 5446 RTU. This field does not appear if the card is an 8540 or if e1a is the IP interface name.

Route to Peer – Net or Host. Must be Net for s1b. Routing method used to get to peer (i.e., host or net). This field does not appear if the card is an 8540 or if e1a is the IP interface name.

NOTE: If you have made any changes to this screen, you must do a card reset or restart the Ethernet interface.

Control (Control Interface)

A-C-C

 

 

Gives the user the ability to restart, stop, and monitor (up, down, or testing) the current state of an interface.

This screen is populated depending on your entry in the Command and Interface Name fields. For example, if you select Monitor mode and enter s1b for the Interface name, the following information is displayed: Type, State, Link protocol, IP state, Uptime, Inactive, Connect time, Port, Local IP addr, and Peer IP addr.

3-16

April 2000

8000-A2-GB20-50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents HOTWIREr 8540 and 8546 Radsl Cards Copyright E 2000 Paradyne Corporation All rights reserved Contents Radsl Card Configuration Glossary Index Contents About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related DocumentsVii Viii Hotwire DSL System Description What is the Hotwire DSL System?Central Office CO Customer Premises CP OptionalHotwire DSL Chassis InputApril Front View of a Hotwire 8820 GranDSLAM Chassis DSL Card MCP CardRadsl Cards Use this MCC Card This Hotwire ChassisMCC Card Software Functionality FeaturesLevels of Access Configuring the DSL Cards Monitoring the DSL CardsTroubleshooting and Diagnostics Hotwire DSL System Description Hotwire Menus and Screens Menu and Screen FormatsComponents of a Hotwire Menu Components of a Hotwire Screen Luserlogin or Ruserlogin where L indicates a local loginCommonly Used Navigation Keys Keys DefinitionCommunications Controller MCC Card User’s Guide User Login Screen Hotwire Chassis Hotwire Menu HierarchyHotwire Chassis Main Menu Diagnostics Hotwire DSL MenuHotwire DSL ApplicationsDSL Card Configuration Menu Logging In to the System DSL Card Monitoring MenuCard Selection Screen Column Position Display Description Heading R D U X XManually Logging Out Accessing the Hotwire DSL MenuExiting From the System Automatically Logging OutHotwire Menus and Screens Port Naming Conventions Radsl Card ConfigurationOverview For the Management Domain, perform task On the . . . See Configuring the MCC Card, DSL Cards, and RTUsFor each Service Domain See Perform task MCC Card DCE ManagerServer 10BT DCE Manager Router CardDCE Manager Server DCE Manager RouterISP Router 85468540 DSL Configuration Card Status Screens Card Info System Information DNS Setup Configure DNSCard Status Options 1 Nvram Clear Screen Clear Nvram Card Status Options 2Time/Date Card Status Options 3 Nvram Config LoaderCard Reset Reset System DOS MachineApply Download Card Status Menu Options 4Download Code Download Code and Apply Download Ethernet Port DSL Configuration Ports ScreensPorts Options 1 Ports Options 2 DSL Ports DSL ParametersThresholds for Trap Messages Ports Options 3DSL Ports DSL Parameters cont’d General Interfaces DSL Configuration Interfaces ScreensInterfaces Options 1 Control Control Interface Interfaces Options 2IP Network Negotiate Options Echo Policy Default =Interfaces Options 3 Link OptionsDSL Configuration Users Screens Users * Configure Account Users OptionsDSL Configuration IP Router Screens Message Meaning IP Router Options 1 Static RoutesFilter Table IP Router Options 2Martian Networks Delete Rule Yes/No IP Router Filters IP Filter ConfigurationIP Router Options 3 IP Router Options 4 DSL Configuration Snmp Screens Management System Source Validation for Radsl CardsCommunities/Traps Snmp Communities/Traps Snmp OptionsSecurity Snmp Security DSL Configuration Dhcp Relay Screens Configuring Dhcp Relay Agent dynamic addressing Select Configuration → Dhcp Relay → Domain Names A-G-AInterface IP Address Read-only Dhcp Relay OptionsDomain Names ServersDSL Configuration RTU Screens RTU Options RTU SelectionMonitoring the Hotwire DSL System DSL Monitoring MenuDSL Monitoring Card Status Screens Card Info General Card Information Login HistoryCard Status Options DSL Monitoring Physical Layer Screens Ether Statistics Ethernet Statistics Physical Layer Options 1Active List Active Ports List Physical Layer Options 2 Hdlc Bus Stats Hdlc Bus StatisticsPhysical Layer Options 3 DSL Link Perf DSL Link Performance SummaryAll Data Physical Layer Options 4DSL Perf Stats DSL Performance Stats Customer DataDSL Xmit Status DSL Transmit Stats DSL Error StatsPhysical Layer Options 5 DSL Monitoring Interfaces Screens Status Interface Status Monitor Interfaces OptionsActive List Active Interfaces List DSL Network Protocol Screens Monitoring → Network Protocol B-DUDP Statistics Network Protocol Options 1Socket Statistics Network Protocol Options 2 TCP Data Stats TCP Data StatisticsIP Statistics Network Protocol Options 3TCP Connection Statistics Network Protocol Options 4 Icmp Statistics Icmp Packet StatisticsNetwork Protocol Options 5 Snmp StatisticsNetwork Protocol Options 6 Hdlc Statistics Hdlc StatisticsLCP Stats PPP H B Network Protocol Options 7PPP Stats General H a Ipcp General Stats PPP H CDSL IP Router Screens Route Information Window Routing TableRouting Table Screen ARP Table DSL Configuration RTU Screens RTU Information Diagnostics and Troubleshooting Applications ScreensTraceRoute Ping IP SettingsApplications Options Diagnostic Screens Selftest Diagnostics OptionsAlarms Card Alarms Packet Echo TestMajor Alarms 1 Failure Type Action TroubleshootingChecking Alarms No Response at StartupDSL port Major Alarms 2 Failure Type ActionEthernet port 1. Check cable connections to the DSL chassis RespondingThreshold Minor Alarms 1 Failure Type ActionMargin Link Down Minor Alarms 2 Failure Type ActionError Rate Syslog Messages Example Syslog MessagesExample 3. System Status Message Network Problems Network Problems 1 ActionNetwork Problems 2 Action Interfaces A-CNetwork Problems 3 Action Monitoring the Hotwire DSL SystemDiagnostics and Troubleshooting Download Code Fully Operational System Download CodeApply Download Scenario Two Download Only SystemSnmp Traps Setting Up Snmp Trap FeaturesDSL Snmp Community Strings and Authentication Failure Trap Enable DSL Port Traps DSL Card Traps Table B-1. DSL Card Traps 1 Event Severity Comment Trap #Snmp Traps XDSL margin low Minor Table B-1. DSL Card Traps 4 Event Severity Comment Trap # Enterprise-Specific Traps RTU Related TrapsStandard Traps Table B-2. Standard Traps Event Trap Class CommentSnmp Traps RTU Setup Hotwire 5446 RTU Setup OverviewIP Injection Type IP Address Network Mask Next Hop Router Figure C-1. IP Routing Table ExampleAccessing the Hotwire 5446 RTU IP Injection MIB Downloading the IP Injection ToolAccessing the IP Injection Tool Community String Entries IP and Device MIBs Supported Additional pdn-common MIBs SupportedConfiguration Requirements Network Management Systems Using a MIB Browser From an Snmp workstationProcedures MIB Browser TechniquesIP Injection Tool Group Objects Table Viewable 5446 RTU ARP Table Glossary Filter EthernetEthernet address Gateway addressPacket OpenLane DCEManager Pots splitterTraceRoute TelnetTerminal emulation UpstreamIndex NumbersIN-2
Related manuals
Manual 161 pages 59.8 Kb Manual 12 pages 4.86 Kb
Top Page Image Contents