Patton electronic 3088RC user manual S2-6 DTE Loops, S2-6 Setting, S2-7 DTE Interface Type

Page 18

S2-6: DTE Loops

The V.35 interface provides two pins, one to request an LAL and the other to request an RDL. If DTE loops are enabled, the 3088RC/A/I will start a local loopback or a remote loopback when these pins are asserted. If DTE loops are disabled, these requests will be ignored.

S2-6

Setting

ON

Enabled

OFF

Disabled

 

 

S2-7: DTE Interface Type

The DTE interface type needs to be set based on the rear module. Set to E1 if using the /K model. Set to normal if using any other model.

S2-7

DTE Interface Type

ON

E1

OFF

Normal

 

 

S3-1 through S3-8: Management Address

Each rack card in a chassis must have a unique management address. The 1001CC and 1001MC use this address to activate and deactivate the rack card's management interface. This is necessary because all rack cards in a chassis communicate over the same bus, so only one card can be active at a time.

This address can be set to any value between 0 and 255. Set S3 to the binary representation of the number (ON=0 and OFF=1). S3-8 is the most signiÞcant bit.

3.4 ABOUT SYSTEM RESET MODE

To enter system reset mode, switch all DIP switches to the OFF position and power cycle the unit. You can use a VT100 emulator conÞgured for 19200 bps/1 stop bit/ no parity/ XON-XOFF ßow control to access the console. Upon restart, you will see the message “Reset Mode”. The 3088RC automatically communicates through the 1001CC in reset mode, and does not wait for its address.

System reset mode provides two functions: software upgrades and con- Þguration reset to factory defaults.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents User Manual Warranty Information ConfigurationGeneral Information Installation OperationSpecifications Model 3088RC Interface Pin AssignmentsCompliance Warranty InformationSafety Compliance EMC ComplianceFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityService Authorized European RepresentativeTel +1 301 Email support@patton.com Safety When Working with Electricity Device firstFeatures General InformationDescription Serial Interface Types Configuration About Software CLI ConfigurationAbout Harware DIP Switch Configuration Configuring the DIP Switches V.35, X.21, and Ethernet Models Position FunctionS1-1 through S1-7 Data Rate S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps2240 S2-2 Line Probe S1-8 TX Clock Setting DescriptionS2-1 Front Panel Switches S2-3 Annex A/BS2-4 through S2-5 Clock Mode S2-4 S2-5 Clock Mode DescriptionCPE-Side Modem CO-Side Modem S2-6 DTE Loops S2-6 SettingAbout System Reset Mode S2-7 DTE Interface TypeSoftware Upgrades ConÞguration Reset to Factory DefaultsConfiguring Through the Console DSL sync state describes whether no sync words have Console Help Commands DSL Line Condition Good or PoorSystem ConÞguration Commands System Status Commands DSL ConÞguration CommandsDSL Error Monitor Startup Delay Interval Totint DSL Status Command DSL Clear Errcntrs CommandStrap Function Position 1&2 Position 2&3 Configuring the V.35 Rear CardModel 1001RCM13445 & 1001RCM134TB Strap Settings JB3Configuring the X.21 Rear Card Model 1001RCM11545& 1001RCM115TB Strap SettingsJB4 S1-1 Line Framing & Coding Configuring the E1 Rear CardDIP Switch ConÞguration Line Coding OptionsOff Disabled Enabled Module Rear Panels, Showing Location of Connectors Making Interface ConnectionsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Connecting the Interface Driver Board Driver Board mounted on Model 3088RCConnecting to the 10Base-T Ethernet Port RC/C/AI Ethernet PortPage LED Status Monitors RJ-45 Line InterfacePage Model 1001R14 Rack Chassis InstallationRack Power Supply More informationPowering Up Your 1001R14 Rack Installing Model 3088RC Series Into the ChassisConnecting the Twisted Pair Interface Interconnecting cables shall be acceptable forModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 Serial Inter Face Connecting the Model 3088RC/A/I V.35 to a DTE deviceConnecting the Model 3088RC/A/I V.35 to a DCE device Connecting the Model 3088RC/A/I to V.35 Serial DCEConnecting the Model 3088RC/D/V X.21 Serial Inter Face Connecting the Model 3088RC/D/V X.21 to a DCE or DTE deviceConnecting the 3088RC/K/K E1 Interface Connecting the 3088RC/C/AI Ethernet InterfaceLED LED Status IndicatorsOperation Color DescriptionTest Modes LoopbacksPatterns Remote Console OperationEstablishing a Remote Console Session Console Remote console connection is open Is a screenshot of opening a typical remote console session Differences in Local and Remote Control Session Behavior Remote control session with LAL diagramSoftware Upgrade To communicate with the far-end 3088RCReset Configuration to Factory Default Appendix a Serial ConnectorDiagnostics Clocking ModesLine Rates DSL Line Transmission LineLine Coding Line InterfaceRJ-11 NON-SHIELDED DSL Port Pin # SignalAppendix B V.35 InterfaceE1 Interface X.21 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents