Patton electronic 3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card user manual

Page 36

Status. Blinks yellow from one to eleven times to indicate system status. Each pulse pattern is separated by a 2 second “off” period. Greater pulse patterns have higher priority (buffer saturation has greater priority than an empty MAC table). Valid system statuses are:

•1 pulse = system status ok

•2 pulses = No MAC entries in the MAC address table

•3 pulses = Clear to send (CTS) or Carrier Detect (DCD) from base unit are not asserted

•4 pulses = IMRC2/IA buffer is saturated

•5 pulses = WAN receive frame(s) too large

•6 pulses = WAN receive frame(s) not Octet aligned

•7 pulses = WAN receive frame(s) aborted

•8 pulses = Detected WAN receive frame(s) with bad CRC

•9 pulses = Detected LAN receive frame(s) too large

•10 pulses = Detected LAN receive frame(s) not Octet aligned

•11 pulses = Detected LAN receive frame(s) with bad CRC

After a status code is displayed eight times and the associated condition is removed, the status code will no longer appear.

Link. Glows green to indicate good link integrity on the 10Base-T twisted pair line.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents User Manual Warranty Information ConfigurationGeneral Information Installation OperationSpecifications Model 3088RC Interface Pin AssignmentsWarranty Information Safety ComplianceCompliance EMC ComplianceFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityService Authorized European RepresentativeTel +1 301 Email support@patton.com Safety When Working with Electricity Device firstFeatures General InformationDescription Serial Interface Types Configuration About Software CLI ConfigurationAbout Harware DIP Switch Configuration Configuring the DIP Switches V.35, X.21, and Ethernet Models Position FunctionS1-1 through S1-7 Data Rate S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps2240 S1-8 TX Clock Setting Description S2-1 Front Panel SwitchesS2-2 Line Probe S2-3 Annex A/BS2-4 through S2-5 Clock Mode S2-4 S2-5 Clock Mode DescriptionCPE-Side Modem CO-Side Modem S2-6 Setting About System Reset ModeS2-6 DTE Loops S2-7 DTE Interface TypeSoftware Upgrades ConÞguration Reset to Factory DefaultsConfiguring Through the Console DSL sync state describes whether no sync words have Console Help Commands DSL Line Condition Good or PoorSystem ConÞguration Commands System Status Commands DSL ConÞguration CommandsDSL Error Monitor Startup Delay Interval Totint DSL Status Command DSL Clear Errcntrs CommandConfiguring the V.35 Rear Card Model 1001RCM13445 & 1001RCM134TB Strap SettingsStrap Function Position 1&2 Position 2&3 JB3Configuring the X.21 Rear Card Model 1001RCM11545& 1001RCM115TB Strap SettingsJB4 Configuring the E1 Rear Card DIP Switch ConÞgurationS1-1 Line Framing & Coding Line Coding OptionsOff Disabled Enabled Module Rear Panels, Showing Location of Connectors Making Interface ConnectionsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Connecting the Interface Driver Board Driver Board mounted on Model 3088RCConnecting to the 10Base-T Ethernet Port RC/C/AI Ethernet PortPage LED Status Monitors RJ-45 Line InterfacePage Installation Rack Power SupplyModel 1001R14 Rack Chassis More informationPowering Up Your 1001R14 Rack Installing Model 3088RC Series Into the ChassisConnecting the Twisted Pair Interface Interconnecting cables shall be acceptable forModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 Serial Inter Face Connecting the Model 3088RC/A/I V.35 to a DTE deviceConnecting the Model 3088RC/A/I V.35 to a DCE device Connecting the Model 3088RC/A/I to V.35 Serial DCEConnecting the Model 3088RC/D/V X.21 Serial Inter Face Connecting the Model 3088RC/D/V X.21 to a DCE or DTE deviceConnecting the 3088RC/K/K E1 Interface Connecting the 3088RC/C/AI Ethernet InterfaceLED Status Indicators OperationLED Color DescriptionTest Modes LoopbacksPatterns Remote Console OperationEstablishing a Remote Console Session Console Remote console connection is open Is a screenshot of opening a typical remote console session Differences in Local and Remote Control Session Behavior Remote control session with LAL diagramSoftware Upgrade To communicate with the far-end 3088RCReset Configuration to Factory Default Serial Connector DiagnosticsAppendix a Clocking ModesTransmission Line Line CodingLine Rates DSL Line Line InterfacePin # Signal Appendix BRJ-11 NON-SHIELDED DSL Port V.35 InterfaceE1 Interface X.21 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents