Patton electronic RocketLink-G NTU Rack Mount G.SHDSL Modem Card Operation, LED Status Indicators

Page 45

5.0 OPERATION

Once the Model 3088RC is properly conÞgured and installed, it should operate transparently. These sections describes functions of the LED status indicators, and the use of the built-in loopback test modes.

5.1 LED STATUS INDICATORS

The Model 3088RC features four front panel LEDs that monitor the opera- tion of the rack card. Figure 17 shows the front panel location of each LED. Table 1 describes each LED’s function.

 

 

3088RC

 

 

RocketLink-G NTU

 

 

 

–Power

 

 

 

–DSL

 

 

 

–TERM

 

 

 

–TM/ER

 

 

Remote

Local

 

 

511

511/E

 

Figure 17. The Model 3088RC Series’ front panel LEDs

 

Table 1: Model 3088RC front panel LED descriptiont

LED

Color

 

Description

Power

Green

Flashing = POST

 

 

Solid = Power is on

DSL

Green

Flashing = Training

 

 

Solid = DSL Link

TERM

Yellow

Solid = Serial port is active

TM/ER

Green

Solid = Test mode is active

 

 

Blinking = Test mode error

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents User Manual Warranty Information ConfigurationGeneral Information Operation InstallationModel 3088RC Interface Pin Assignments SpecificationsSafety Compliance Warranty InformationCompliance EMC ComplianceRadio and TV Interference FCC Part FCC Part 68 Acta StatementCE Declaration of Conformity Industry Canada NoticeService Authorized European RepresentativeTel +1 301 Email support@patton.com Device first Safety When Working with ElectricityFeatures General InformationDescription Serial Interface Types Configuration About Software CLI ConfigurationAbout Harware DIP Switch Configuration Position Function Configuring the DIP Switches V.35, X.21, and Ethernet ModelsS1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps S1-1 through S1-7 Data Rate2240 S2-1 Front Panel Switches S1-8 TX Clock Setting DescriptionS2-2 Line Probe S2-3 Annex A/BS2-4 through S2-5 Clock Mode S2-4 S2-5 Clock Mode DescriptionCPE-Side Modem CO-Side Modem About System Reset Mode S2-6 SettingS2-6 DTE Loops S2-7 DTE Interface TypeSoftware Upgrades ConÞguration Reset to Factory DefaultsConfiguring Through the Console DSL sync state describes whether no sync words have DSL Line Condition Good or Poor Console Help CommandsSystem ConÞguration Commands System Status Commands DSL ConÞguration CommandsDSL Error Monitor Startup Delay Interval Totint DSL Clear Errcntrs Command DSL Status CommandModel 1001RCM13445 & 1001RCM134TB Strap Settings Configuring the V.35 Rear CardStrap Function Position 1&2 Position 2&3 JB3Configuring the X.21 Rear Card Model 1001RCM11545& 1001RCM115TB Strap SettingsJB4 DIP Switch ConÞguration Configuring the E1 Rear CardS1-1 Line Framing & Coding Line Coding OptionsOff Disabled Enabled Making Interface Connections Module Rear Panels, Showing Location of ConnectorsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Driver Board mounted on Model 3088RC Connecting the Interface Driver BoardRC/C/AI Ethernet Port Connecting to the 10Base-T Ethernet PortPage RJ-45 Line Interface LED Status MonitorsPage Rack Power Supply InstallationModel 1001R14 Rack Chassis More informationInstalling Model 3088RC Series Into the Chassis Powering Up Your 1001R14 RackInterconnecting cables shall be acceptable for Connecting the Twisted Pair InterfaceModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 to a DTE device Connecting the Model 3088RC/A/I V.35 Serial Inter FaceConnecting the Model 3088RC/A/I to V.35 Serial DCE Connecting the Model 3088RC/A/I V.35 to a DCE deviceConnecting the Model 3088RC/D/V X.21 to a DCE or DTE device Connecting the Model 3088RC/D/V X.21 Serial Inter FaceConnecting the 3088RC/C/AI Ethernet Interface Connecting the 3088RC/K/K E1 InterfaceOperation LED Status IndicatorsLED Color DescriptionLoopbacks Test ModesPatterns Remote Console OperationEstablishing a Remote Console Session Console Remote console connection is open Is a screenshot of opening a typical remote console session Remote control session with LAL diagram Differences in Local and Remote Control Session BehaviorTo communicate with the far-end 3088RC Software UpgradeReset Configuration to Factory Default Diagnostics Serial ConnectorAppendix a Clocking ModesLine Coding Transmission LineLine Rates DSL Line Line InterfaceAppendix B Pin # SignalRJ-11 NON-SHIELDED DSL Port V.35 InterfaceX.21 Interface E1 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents