Patton electronic 3088RC user manual JB4, Configuring the X.21 Rear Card

Page 26

SGND & FRGND (JB4). In the connected position, this strap links Signal Ground and frame ground through a 100 ohm resistor. In the open posi- tion, signal ground is disconnected from frame ground.

JB4

Description

Position 1&2

SGND and FRGND Connected

Position 2&3

SGND and FRGND Not Connected

 

 

3.7 CONFIGURING THE X.21 REAR CARD

The X.21 interface card is conÞgured by setting the conÞguration straps located on the PC board.

Model 1001RCM11545& 1001RCM115TB Strap Settings

Figure 3 shows strap locations for the Model 1001RCM115XX (DB-15) rear cards. These straps determine various grounding characteristics for the terminal interface and twisted pair lines. JB3 and JB4 are user con- Þgurable.

JB3 1 2 3

JB4

1 2 3

Figure 3. 1001RCM115XX strap locations

The table below provides an overview of interface strap functions for the rear interface cards. Following the table overview are detailed descrip- tions of each strap’s function.

Strap

Function

Position 1&2

Position 2&3

JB3

DTE Shield (Pin1) & FRGND

Connected

Open*

JB4

FRGND & SGND (Pin 8)

Connected

Open*

 

 

 

 

* Indicates default setting

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents User Manual General Information Warranty InformationConfiguration Installation OperationSpecifications Model 3088RC Interface Pin AssignmentsCompliance Warranty InformationSafety Compliance EMC ComplianceFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityTel +1 301 Email support@patton.com ServiceAuthorized European Representative Safety When Working with Electricity Device firstDescription FeaturesGeneral Information Serial Interface Types About Harware DIP Switch Configuration ConfigurationAbout Software CLI Configuration Configuring the DIP Switches V.35, X.21, and Ethernet Models Position FunctionS1-1 through S1-7 Data Rate S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps2240 S2-2 Line Probe S1-8 TX Clock Setting DescriptionS2-1 Front Panel Switches S2-3 Annex A/BCPE-Side Modem CO-Side Modem S2-4 through S2-5 Clock ModeS2-4 S2-5 Clock Mode Description S2-6 DTE Loops S2-6 SettingAbout System Reset Mode S2-7 DTE Interface TypeConfiguring Through the Console Software UpgradesConÞguration Reset to Factory Defaults DSL sync state describes whether no sync words have Console Help Commands DSL Line Condition Good or PoorSystem ConÞguration Commands DSL Error Monitor Startup Delay Interval Totint System Status CommandsDSL ConÞguration Commands DSL Status Command DSL Clear Errcntrs CommandStrap Function Position 1&2 Position 2&3 Configuring the V.35 Rear CardModel 1001RCM13445 & 1001RCM134TB Strap Settings JB3JB4 Configuring the X.21 Rear CardModel 1001RCM11545& 1001RCM115TB Strap Settings S1-1 Line Framing & Coding Configuring the E1 Rear CardDIP Switch ConÞguration Line Coding OptionsOff Disabled Enabled Module Rear Panels, Showing Location of Connectors Making Interface ConnectionsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Connecting the Interface Driver Board Driver Board mounted on Model 3088RCConnecting to the 10Base-T Ethernet Port RC/C/AI Ethernet PortPage LED Status Monitors RJ-45 Line InterfacePage Model 1001R14 Rack Chassis InstallationRack Power Supply More informationPowering Up Your 1001R14 Rack Installing Model 3088RC Series Into the ChassisConnecting the Twisted Pair Interface Interconnecting cables shall be acceptable forModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 Serial Inter Face Connecting the Model 3088RC/A/I V.35 to a DTE deviceConnecting the Model 3088RC/A/I V.35 to a DCE device Connecting the Model 3088RC/A/I to V.35 Serial DCEConnecting the Model 3088RC/D/V X.21 Serial Inter Face Connecting the Model 3088RC/D/V X.21 to a DCE or DTE deviceConnecting the 3088RC/K/K E1 Interface Connecting the 3088RC/C/AI Ethernet InterfaceLED LED Status IndicatorsOperation Color DescriptionTest Modes LoopbacksEstablishing a Remote Console Session PatternsRemote Console Operation Console Remote console connection is open Is a screenshot of opening a typical remote console session Differences in Local and Remote Control Session Behavior Remote control session with LAL diagramSoftware Upgrade To communicate with the far-end 3088RCReset Configuration to Factory Default Appendix a Serial ConnectorDiagnostics Clocking ModesLine Rates DSL Line Transmission LineLine Coding Line InterfaceRJ-11 NON-SHIELDED DSL Port Pin # SignalAppendix B V.35 InterfaceE1 Interface X.21 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents