Patton electronic 3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card Off Disabled Enabled

Page 28

•Alternate Mark Inversion (AMI): AMI coding does not inherently account for ones density. To meet this requirement, you should ensure that the data inherently meets pulse density requirements.

Switch S1-2 : CRC-4 Multiframe. CRC-4 Multiframe uses Time Slot zero to carry CRC-4 information. When CRC-4 is enabled (ON), the unit synchronizes to the CRC-4multi-frame protocol.

S1-2

Option

Off

On

Disabled

Enabled

 

 

Note When the data rate is set to 2048 Kbps, K Module transmits user data on all 32 timeslots, ignoring framing information. In this case, Switch S1-2 will be ignored.

Switch S1-3 : Clear Channel Mode. When S1-3 is at Off position, the K Module is running in G.703 clear channel mode. When S1-3 is at On position, the K Module is running in G.704 framed mode. When the K Module is set to framed mode, channel 0 will be used to pass G.704 framing information which results in a maximum bandwidth of 1984kbps for user data.

S1-3

Option

Off

On

Clear Channel Mode (G.703)

Framed Mode

 

(G.704)

 

 

Switch S1-4 Through S1-8 : Reserved. Reserved for future use and should be set to OFF.

Jumper ConÞguration

The 3088RC/K model has four jumpers (two position headers): JP4, JP5, JP6, and JP7. These jumpers are used to select input and output imped- ance matching between the module and external line. See Appendix E for jumper locations.

The following is a description of the jumper settings with respect to the front panel connectors.

1.For a 75 ohm connection (coax) install JP4 - JP7 (default).

2.For a 120 ohm connection (RJ-48C) remove JP4 - JP7.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents User Manual Configuration Warranty InformationGeneral Information Installation OperationSpecifications Model 3088RC Interface Pin AssignmentsWarranty Information Safety ComplianceCompliance EMC ComplianceFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityAuthorized European Representative ServiceTel +1 301 Email support@patton.com Safety When Working with Electricity Device firstGeneral Information FeaturesDescription Serial Interface Types About Software CLI Configuration ConfigurationAbout Harware DIP Switch Configuration Configuring the DIP Switches V.35, X.21, and Ethernet Models Position FunctionS1-1 through S1-7 Data Rate S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps2240 S1-8 TX Clock Setting Description S2-1 Front Panel SwitchesS2-2 Line Probe S2-3 Annex A/BS2-4 S2-5 Clock Mode Description S2-4 through S2-5 Clock ModeCPE-Side Modem CO-Side Modem S2-6 Setting About System Reset ModeS2-6 DTE Loops S2-7 DTE Interface TypeConÞguration Reset to Factory Defaults Software UpgradesConfiguring Through the Console DSL sync state describes whether no sync words have Console Help Commands DSL Line Condition Good or PoorSystem ConÞguration Commands DSL ConÞguration Commands System Status CommandsDSL Error Monitor Startup Delay Interval Totint DSL Status Command DSL Clear Errcntrs CommandConfiguring the V.35 Rear Card Model 1001RCM13445 & 1001RCM134TB Strap SettingsStrap Function Position 1&2 Position 2&3 JB3Model 1001RCM11545& 1001RCM115TB Strap Settings Configuring the X.21 Rear CardJB4 Configuring the E1 Rear Card DIP Switch ConÞgurationS1-1 Line Framing & Coding Line Coding OptionsOff Disabled Enabled Module Rear Panels, Showing Location of Connectors Making Interface ConnectionsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Connecting the Interface Driver Board Driver Board mounted on Model 3088RCConnecting to the 10Base-T Ethernet Port RC/C/AI Ethernet PortPage LED Status Monitors RJ-45 Line InterfacePage Installation Rack Power SupplyModel 1001R14 Rack Chassis More informationPowering Up Your 1001R14 Rack Installing Model 3088RC Series Into the ChassisConnecting the Twisted Pair Interface Interconnecting cables shall be acceptable forModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 Serial Inter Face Connecting the Model 3088RC/A/I V.35 to a DTE deviceConnecting the Model 3088RC/A/I V.35 to a DCE device Connecting the Model 3088RC/A/I to V.35 Serial DCEConnecting the Model 3088RC/D/V X.21 Serial Inter Face Connecting the Model 3088RC/D/V X.21 to a DCE or DTE deviceConnecting the 3088RC/K/K E1 Interface Connecting the 3088RC/C/AI Ethernet InterfaceLED Status Indicators OperationLED Color DescriptionTest Modes LoopbacksRemote Console Operation PatternsEstablishing a Remote Console Session Console Remote console connection is open Is a screenshot of opening a typical remote console session Differences in Local and Remote Control Session Behavior Remote control session with LAL diagramSoftware Upgrade To communicate with the far-end 3088RCReset Configuration to Factory Default Serial Connector DiagnosticsAppendix a Clocking ModesTransmission Line Line CodingLine Rates DSL Line Line InterfacePin # Signal Appendix BRJ-11 NON-SHIELDED DSL Port V.35 InterfaceE1 Interface X.21 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents