Patton electronic user manual Connecting the Model 3088RC/A/I V.35 to a DCE device

Page 42

Connecting the Model 3088RC/A/I (V.35) to a “DCE” device

The Model 3088RC/A/I provides a V.35 DCE (data circuit terminating equipment) interface on a M/34 connector. As a DCE, this interface is designed to connect to DTE equipment, such as a router. However, con- necting the 3088RC/A/I to another DCE device, such as a multiplexer or G.703 E1 NTU, requires a tailcircuit cable. When connecting the V.35 interface of the Model 3088RC/A/I to your DCE device, use a V.35 tail cir- cuit cable. Some applications may also require the installation of a tail- circuit buffer to account for small differences in clock frequency between the 3088RC/A/I and the V.35 DCE (multiplexer).

3088RC

RocketLink-G NTU

–Power

–DSL

–TERM

–TM/ER

Remote Local

511 511/E

Remote Model 3088RC

DSL Span

G.703 E1 NTU

3088RC

Tail-circuit cable

RocketLink-G NTU

 

–Power

 

 

 

–DSL

 

 

–TERM

(DCE)

 

–TM/ER

 

 

Remote

Local

 

511

511/E

 

 

 

Model 3088RC/A (DCE)

Figure 15. Connecting the Model 3088RC/A/I to V.35 Serial DCE

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents User Manual Warranty Information ConfigurationGeneral Information Installation OperationSpecifications Model 3088RC Interface Pin AssignmentsCompliance Warranty InformationSafety Compliance EMC ComplianceFCC Part 68 Acta Statement Radio and TV Interference FCC PartIndustry Canada Notice CE Declaration of ConformityService Authorized European RepresentativeTel +1 301 Email support@patton.com Safety When Working with Electricity Device firstFeatures General InformationDescription Serial Interface Types Configuration About Software CLI ConfigurationAbout Harware DIP Switch Configuration Configuring the DIP Switches V.35, X.21, and Ethernet Models Position FunctionS1-1 through S1-7 Data Rate S1-1 S1-2 S1-3 S1-4 S1-5 S1-6 S1-7 Data Rate Kbps2240 S2-2 Line Probe S1-8 TX Clock Setting DescriptionS2-1 Front Panel Switches S2-3 Annex A/BS2-4 through S2-5 Clock Mode S2-4 S2-5 Clock Mode DescriptionCPE-Side Modem CO-Side Modem S2-6 DTE Loops S2-6 SettingAbout System Reset Mode S2-7 DTE Interface TypeSoftware Upgrades ConÞguration Reset to Factory DefaultsConfiguring Through the Console DSL sync state describes whether no sync words have Console Help Commands DSL Line Condition Good or PoorSystem ConÞguration Commands System Status Commands DSL ConÞguration CommandsDSL Error Monitor Startup Delay Interval Totint DSL Status Command DSL Clear Errcntrs CommandStrap Function Position 1&2 Position 2&3 Configuring the V.35 Rear CardModel 1001RCM13445 & 1001RCM134TB Strap Settings JB3Configuring the X.21 Rear Card Model 1001RCM11545& 1001RCM115TB Strap SettingsJB4 S1-1 Line Framing & Coding Configuring the E1 Rear CardDIP Switch ConÞguration Line Coding OptionsOff Disabled Enabled Module Rear Panels, Showing Location of Connectors Making Interface ConnectionsOhm Dual Coaxial G.703 Interface Connecting the Ethernet Rear Card Connecting the Interface Driver Board Driver Board mounted on Model 3088RCConnecting to the 10Base-T Ethernet Port RC/C/AI Ethernet PortPage LED Status Monitors RJ-45 Line InterfacePage Model 1001R14 Rack Chassis InstallationRack Power Supply More informationPowering Up Your 1001R14 Rack Installing Model 3088RC Series Into the ChassisConnecting the Twisted Pair Interface Interconnecting cables shall be acceptable forModel 3088RC V.35/X.21 interfaces Connecting the Model 3088RC/A/I V.35 Serial Inter Face Connecting the Model 3088RC/A/I V.35 to a DTE deviceConnecting the Model 3088RC/A/I V.35 to a DCE device Connecting the Model 3088RC/A/I to V.35 Serial DCEConnecting the Model 3088RC/D/V X.21 Serial Inter Face Connecting the Model 3088RC/D/V X.21 to a DCE or DTE deviceConnecting the 3088RC/K/K E1 Interface Connecting the 3088RC/C/AI Ethernet InterfaceLED LED Status IndicatorsOperation Color DescriptionTest Modes LoopbacksPatterns Remote Console OperationEstablishing a Remote Console Session Console Remote console connection is open Is a screenshot of opening a typical remote console session Differences in Local and Remote Control Session Behavior Remote control session with LAL diagramSoftware Upgrade To communicate with the far-end 3088RCReset Configuration to Factory Default Appendix a Serial ConnectorDiagnostics Clocking ModesLine Rates DSL Line Transmission LineLine Coding Line InterfaceRJ-11 NON-SHIELDED DSL Port Pin # SignalAppendix B V.35 InterfaceE1 Interface X.21 InterfaceRS-232 Console Interface Page

3088RC, RocketLink-G NTU Rack Mount G.SHDSL Modem Card specifications

The Patton Electronics 3088RC, also known as the RocketLink-G NTU Rack Mount G.SHDSL Modem Card, is a robust and versatile solution designed to enable high-speed data communication over copper lines. This modem card is particularly favored by telecommunications providers and businesses seeking reliable connectivity in demanding environments.

One of the key features of the 3088RC is its G.SHDSL technology, which allows for symmetric data transmission at speeds up to 5.7 Mbps. This symmetric speed makes it ideal for businesses that require the same upload and download speeds, ensuring efficient performance for applications such as video conferencing, cloud services, and file sharing. Furthermore, G.SHDSL offers longer range capabilities compared to traditional DSL technologies, achieving distances up to 12,000 feet or more, depending on line conditions.

The 3088RC is designed for easy integration into existing rack mount installations. It occupies a single 19-inch rack unit, making it a space-efficient option for service providers looking to maximize their hardware capacity. The installation process is straightforward, allowing for quick deployment in various settings, from small offices to larger enterprise environments.

In terms of power, the Patton 3088RC supports both AC and DC power inputs, providing flexibility in installation. The card also features built-in network management capabilities. This includes SNMP support for remote monitoring and troubleshooting, allowing IT administrators to keep track of performance and quickly identify issues without needing to be physically present.

Moreover, the device guarantees high reliability with its advanced error correction techniques, which enhance data integrity over longer distances and in environments with significant interference. Equipped with a robust design, the 3088RC operates well in fluctuating temperatures, ensuring durability and consistent performance.

Security is also a priority, as the RocketLink-G offers features that protect against unauthorized access and data breaches. This is particularly crucial for businesses handling sensitive information.

To conclude, the Patton Electronics 3088RC RocketLink-G NTU Rack Mount G.SHDSL Modem Card represents a comprehensive solution for reliable high-speed connectivity. Its blend of advanced technology, ease of integration, and focus on performance makes it an attractive choice for service providers and enterprises aiming to enhance their data communications infrastructure.
Top Page Image Contents