Patton electronic 3086 manual Introduction

Page 36

4 • Basic Application Configurations

Model 3086 G.SHDSL Integrated Access Device User Guide

 

 

Introduction

The Model 3086 IAD comes with two data ports: a TDM (V.35, X.21, or T1/E1), and an Ethernet port. TDM port data is not processed by the router or bridge core in the 3086, data is transmitted unprocessed over the DSL link. Data from the Ethernet port is processed by the 3086 bridge or router core and sent inHDLC or ATM encapsulation over the DSL link.

The 3086 can be used as a simple modem – transporting TDM data from a router, multiplexer, or PBX con- nected to the V.35, X.21 or T1/E1 port. In this case the user configures DSL and TDM port features only.

The 3086 can concurrently transport TDM and Ethernet traffic, the TDM and Ethernet ports are activated, and the user must assign DSL bandwidth for both TDM and Ethernet traffic. Since Ethernet layer is activated, the user must configure the routing or bridging features and must choose from HDLC or ATM encapsulation

The 3086 can be used to transport Ethernet traffic only, via its 10/100 Base-T LAN across a campus or across a WAN, in this case, the TDM port is not activated. In addition to configuring the DSL link, the user must configure the routing or bridging features and must choose from HDLC or ATM encapsulation.

Configuration for these applications is presented in the following sections. The 3086 is used to transport TDM data only, TDM plus Ethernet, or Ethernet only data. Since the configuration of the router or bridge and the ATM or HDLC Features are considerably more complex than the DSL and data port layers, we present physi- cal layer configuration of TDM port and TDM port plus Ethernet first as the foundation from which the upper layers can be configured. An extensive section is devoted to the Bridge/Router, and HDLC/ATM appli- cation configuration.

What follows is a brief description and a table summarizing the parameters for bridged and routed WAN ser- vices achieved with the Model 3086.

The basic applications are divided according to whether the application is bridged or routed.

The bridged applications are RFC 1483 Bridged, PPPoA Bridged, and HDLC Bridged.

The routed applications are RFC 1483, PPPoA, IPoA, PPPoE, and HDLC.

Another way of organizing the applications is according to the type of encapsulation: PPP, RFC 1483, or Frame Relay. PPP encapsulation is available as PPPoA bridged or routed and PPPoE. RFC 1483 and Frame Relay can be configured for bridged and routed connections.

36

Introduction

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Shdsl Integrated Access Device Patton Electronics Company, Inc Contents Basic Application Configurations Contents Specialized Configurations 113 Contacting Patton for assistance 143 Cable Recommendations 157 Contents Page About this guide AudienceStructure Precautions Factory default parameters Safety when working with electricityAbout this guide Typographical conventions used in this document General conventionsMouse conventions Chapter contents General InformationModel 3086 G.SHDSL IAD overview General attributesModel 3086 G.SHDSL IAD overview Shdsl Characteristics EthernetTDM Interface Protocol supportPPP Support ATM ProtocolsManagement Security ModelWAN DSL Rear panel connectors and switches Power connectorConsole port outlined in red RJ-11/4 DSL line port uses pins 2 and 3 of the RJ-11 port Ethernet port outlined in greenLine port outlined in yellow Product Overview Product Overview Applications OverviewInternet/Extranet Access IP/FR and TDM AccessIP/FR and Voice over DSL Product OverviewMetro Intranet Access Quick Start Installation Hardware installation Installing the AC power cordWhat you will need Connecting network cables Quick Start InstallationWeb Operation and Configuration PC ConfigurationIP address Quick Start modification IP address has now been successfully changedModel 3086 home page displays see Figure Model 3086 menu structure is shown in onModel 3086 Menu Structure Basic Application Configurations Basic Application Configurations IPoA Routed RFC Introduction Routed WAN Services Bridged WAN Services TDM PortRear panel power and interface connectors Connecting the 3086 serial port to a DTE Connecting the 3086 serial port to a DCEX.21 Ports InterfacesConfiguring the V.35 or X.21 port via DIP switches X.21 PortsDIP switches location Switch Bank S2 Switch Position Function Factory Default Selected OptionSwitch Bank S3 T1 Interface T1 Interface ConnectionT1 Interface Configuration DIP Switch ConfigurationData Rate kbps Figuration only Web Interface Configuration Line Code The 3086 T1 interface uses B8ZSE1 Interface E1 Interface ConnectionDescription of S2 options follows the table E1/CRC S3-8 Setting Web Interface Configuration Using the 3086 as a simple modem TDM data over DSL CLI configurationCLI configuration Wait for configuration saved message… Saving configuration… Web browser configuration Clear Error CountersCircuit ID Intended DSL Data RateIntended Serial Interface Data Rate DSL Rate Number of i BitTerminal Type TDM Plus Ethernet Traffic Selecting PCM mode Selecting the DSL link speedAssigning bandwidth to serial and Ethernet ports Central or Remote terminal Master/SlaveFor 3086 a at the prompt type For 3086 B typeSelect between Annex a and Annex B To select Annex B type Circuit ID Intended Serial Interface Data Rate Interface Type Using the 3086 in Routed or Bridged applications Model 3086 Remote Configuration Steps PPPoH BridgedTwo stand-alone units directly connected Ethernet extension Hdlc Pppoh BridgedLeave User name and Password blank. Click on Apply Model 3086 Central Configuration Steps PPPoH Bridged Model 3086 Remote Configuration Steps PPPoH Routed Network Extension HDLC-PPPoH RoutedModel 3086 G.SHDSL Integrated Access Device User Guide Click on Configure Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Using the 3086 in Routed or Bridged applications Bridged application configurations to a Dslam RFC 1483 Bridged ConfigurationDslam Connections with remote CPE units Model 3086 Remote Configuration Steps RFC 1483 Bridged Model 3086 Central Configuration Steps RFC 1483 Bridged PPPoH Bridged Configuration Dslam Connections with remote CPE units Model 3086 Central Configuration Steps PPPoH Bridged PPPoA Bridged RFC 2364 Configuration Model 3086 Remote Configuration Steps PPPoA BridgedModel 3086 CentralConfiguration Steps PPPoA Bridged VPI = VCI = LLC header mode = off Hdlc header mode = offRouted application configurations to a Dslam Model 3086 Remote Configuration Steps RFC 1483 RoutedRFC 1483 Routed Model 3086 G.SHDSL Integrated Access Device User Guide Basic Application Configurations Model 3086 Central Configuration Steps RFC 1483 Routed One IP interface was called ip1 with an IP addressIp set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations PPPoH Routed Ip set interface ip1 ipaddress 192.168.100.2 Dslam Connections with remote CPE units Basic Application Configurations Model 3086 Central Configuration Steps PPPoH Routed Basic Application Configurations Basic Application Configurations Model 3086 Remote-Client Configuration Steps PPPoA Routed PPPoA Routed RFCUser Namefred Passwoodfredspass Click on Configure ChapBasic Application Configurations Dslam Connections with remote CPE units Model 3086 Central-Server Configuration Steps PPPoA Routed 100 101 Local IP Magic Number MRU 102103 104 105 106 Model 3086 Remote Configuration Steps IPoA Routed IPoA Routed RFC107 108 109 110 Model 3086 Central Configuration Steps IPoA Routed VPI0 VCI700 WAN IP address Click on Apply111 112 Specialized Configurations IP Configurations RouterRIP and RIPv2 Static Route Dhcp Server and RelaySpecialized Configurations 115DNS Client 116DNS Relay Mode 117IP Configurations Security Configuring the IAD 120Configuring the security interfaces Security121 Deleting a Firewall Policy 122Enabling the Firewall Firewall PortfiltersFirewall Policies Firewall policy named item0 is now deletedSecurity Triggers 124125 Scan Attack Block DurationDefault = 86400 seconds Intrusion Detection System IDS126 127 Intrusion Detection System IDS NAT Network Address Translation Enabling NAT 130Global address pool and reserved map NAT Network Address Translation131 132 Monitoring Status Status LEDs 134Diagnostics Software Upgrades ConfigurationProcedure PingDiagnostics Operating Local Analog Loopback LAL-Serial Port LoopOperating Remote Digital Loopback RDL-DSL Loop 137T1/E1 Diagnostics Network Loop138 T1/E1 Local Loop 139QRSS-BIT Error Rate Diagnostics 140Alarms T1/E1 connection StatusTransceiver Status FDL statistics T1 onlyBIT Error Rate V.52 Diagnostics 142Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditReturn for credit policy RMA numbersShipping instructions Contacting Patton for assistancePage Appendix a Compliance information Safety ComplianceRadio and TV Interference FCC Part CE Declaration of ConformityAuthorized European Representative FCC Part 68 Acta StatementIndustry Canada Notice 149150 Appendix B Specifications General Characteristics Shdsl CharacteristicsEthernet 152Sync Serial Interface T1/E1 Interface 3086/RIK and RIT models only64K/G.703 Port 3086/RIF Model Protocol SupportPPP Support ATM ProtocolsManagement 154Dimensions Power and Power Supply SpecificationsSecurity Compliance Standard Requirements156 Appendix C Cable Recommendations DSL Cable Ethernet CableAdapter Foot 3 m, RJ-11/RJ-11 refer to RJ-11non-shielded port onAppendix D Physical Connectors Assuming the MDI-X switch is in the out position RJ-45 shielded 10/100 Ethernet portRJ-11 non-shielded port RJ-45 non-shielded RS-232 console port EIA-56135 M/34 Connector 35 DB-25 Female ConnectorPhysical Connectors Serial portPower input 21 DB-15 Connector E1/T1 RJ-48C ConnectorIEC 320 connector two prong 162Appendix E Command Line Interface CLI Operation 163CLI Terminology Produces a list of numbered transport objectsLocal VT-100 emulation Remote TelnetUsing the Console Command Line Interface CLI OperationThen 165Administering user accounts Setting user passwordsAdding new users Following information is returnedChanging user settings Controlling login accessControlling user access Shdsl CommandsTo establish the DSL link For CPE remote unit168 169 170 Appendix F Interworking Functions Information Interworking Functions Information LMI Configuration Options ManagementType Default Value nomaintenanceFrame Relay Local Management Interface 173MgtAutoStart Default Value False T391Value Default ValueT392Value Default Value FullReportCycle Default ValueCLI Configuration Methods Show current configurationCommand lmi show Set configuration variableFrame Relay Service Interworking FRF.8 Web Configuration MethodsFRS Configuration Options DE MappingTranslation Mode Fecn Mapping177 FRS Name 178CLI Configuration Method Command frs set group # variable valueShow one of the eight groups Set variable attributes on a specified groupSet variable attributes on a specified channel FRS Overview Screen180 Group/Channel Level Configuration Screen 181FRN Configuration Options Frame Relay Network Interworking FRF.5182 Port Level Configuration Options 183Channel Level Configuration Options 184CLI Configuration Methods for Port Level Management List all ports available to the systemShow detailed information about a specific port 185Command frn set port# variable value Configuration Management of the Channel Level VariablesUnderstanding the Channel Level View 186Set Configuration Variables associated with the Channels Command frn set port# channel # variable value187 Port Level Information Screen 188Channel Level Information Screen Packet Information Screen189 Frame Relay Configuration Options Frame Relay CLI Configuration OptionsFrame Relay Ethernet Based Operations Clear all Frame Relay Transports Delete the specified transportList all active Frame Relay Channels 191Serial Interface Configuration Web Based Configuration of the Frame Relay ChannelConfiguration Variables Available Clock ModeShow current configuration settings Gain help about the Serial Interface193 Web Interface Configurations Ping commands from the CLI InterfacePing and Trace Route 194Trace Route from the CLI Interface Define Usage ip tracerouteStart Trace Route ip traceroute start 195Backup and Restore Features Backup ConfigurationRestore Configuration Ping and traceroute from the web interface
Related manuals
Manual 2 pages 38.76 Kb
Top Page Image Contents