TP-Link TL-WR941ND manual Rear Panel, ¾ Reset button

Page 10

TL-WR941N/TL-WR941ND

Wireless N Router

1.4.2 The Rear Panel

Figure 1-2 Rear Panel sketch

The following parts are located on the rear panel (View from left to right).

¾Power socket: The Power socket is where you will connect the power adapter. Please use

the power adapter provided with this TL-WR941N/941ND Wireless N Router.

¾LAN (1,2,3,4): These ports (1, 2, 3, 4) connect the router to the local PC(s).

¾WAN: This WAN port is where you will connect the DSL/cable Modem, or Ethernet.

¾Reset button

There are two ways to reset to the router's factory defaults:

1)Use the Factory Defaults function on System Tools ->Factory Defaults page in the router's Web-based Utility.

2)Use the Factory Default Reset button: Press the Reset button for five seconds and then wait for the router to reboot.

¾Wireless antenna: To receive and transmit the wireless data.

- 5 -

Image 10

Contents TL-WR941N TL-WR941ND Copyright & Trademarks FCC Statement FCC RF Radiation Exposure Statement Country Restriction Reason/remarkContents Dhcp Package Contents Introduction Overview of the RouterMain Features ConventionsFront Panel Panel LayoutName Status Indication ¾ Reset button Rear PanelConnecting the Router Connecting the RouterInstallation Environment Requirements System RequirementsHardware Installation of the TL-WR941ND Wireless N Router Quick Installation Guide TCP/IP configurationSuccess result of Ping command Please check the connection following these stepsQuick Installation Guide 3Login the routerChoose WAN Connection Type Quick Setup Static IP 10 Quick Setup Finish Login Configuring the RouterStatus Quick Setup Router StatusBy PBC Quick Secure Setup functionQSS Method OneMethod Two Add a New DeviceII. By PIN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND 1 LAN Network2 WAN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND WAN PPPoE PPPoE Advanced Settings Wireless MAC CloneWireless Settings 12 Wireless SettingsWireless Security TL-WR941N/TL-WR941ND Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 14 Wireless MAC address Filtering15 Add or Modify Wireless MAC Address Filtering entry Wireless Advanced To access for Filtering RulesWireless Statistics 17 The router attached wireless stationsDhcp Settings DhcpDhcp Clients List 20 Dhcp Clients ListTo Reserve IP addresses Address ReservationTo modify or delete an existing entry Virtual Servers ForwardingDelete To setup a virtual server entry 25 Add or Modify a Virtual Server EntryPort Triggering 27 Add or Modify a Triggering Entry UPnP 3 DMZTo assign a computer or server to be a DMZ server Security Firewall¾ Enable Firewall the general firewall switch is on or off IP FilteringTo add/modify an IP Address filtering entry TL-WR941N/TL-WR941ND Other configurations for the entries Domain FilteringTo Add a Domain filtering entry 35 Add or Modify a Domain Filtering entryMAC Filtering To add or modify a Domain Filtering entryStatic Routing To add additional entries, repeat stepsTo add static routing entries 38 Static Routing40 Dyndns.org Ddns Settings Dynamic DNSTo configure the system manually Time SettingSystem Tools To configure the system automatically FirmwareFactory Defaults Backup & RestoreReboot Password47 Password System logRemote Management StatisticsStatistics Table TCPAppendix a FAQ Figure A-2 PPPoE Connection ModeFigure A-3 MAC Clone Want to use Netmeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the router Figure A-7 Remote ManagementTL-WR941N/TL-WR941ND Appendix B Configuring the PCs Install TCP/IP componentShown in the Figure below ¾ Setting IP address manually Figure B-3Figure B-4 General Appendix C SpecificationsWireless Environmental and PhysicalAppendix D Glossary TL-WR941N/TL-WR941ND

Related manuals

Manual 113 pages 40.69 Kb