TP-Link TL-WR941ND manual II. By PIN

Page 23

TL-WR941N/TL-WR941ND

Wireless N Router

Step 2: Choose Press the button of the new device in two minutes and click Connect..

Step 3: For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the QSS as below, and click Next.

The QSS Configuration Screen of Wireless Adapter

II. By PIN

If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods.

Method One: Enter the PIN into my Router

Step 1: Keep the default QSS Status as Enabled and click the Add device button in Figure 4-2,then the following screen will appear.

- 18 -

Image 23

Contents TL-WR941N TL-WR941ND Copyright & Trademarks FCC Statement Country Restriction Reason/remark FCC RF Radiation Exposure StatementContents Dhcp Package Contents Overview of the Router IntroductionConventions Main FeaturesName Status Indication Panel LayoutFront Panel Rear Panel ¾ Reset buttonSystem Requirements Connecting the RouterInstallation Environment Requirements Connecting the RouterHardware Installation of the TL-WR941ND Wireless N Router TCP/IP configuration Quick Installation GuidePlease check the connection following these steps Success result of Ping command3Login the router Quick Installation GuideChoose WAN Connection Type Quick Setup Static IP 10 Quick Setup Finish Status Configuring the RouterLogin Router Status Quick SetupMethod One Quick Secure Setup functionQSS By PBCAdd a New Device Method TwoII. By PIN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND 2 WAN Network1 LAN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND WAN PPPoE PPPoE Advanced Settings MAC Clone Wireless12 Wireless Settings Wireless SettingsWireless Security TL-WR941N/TL-WR941ND Encryption You can select either Automatic, or Tkip or AES 14 Wireless MAC address Filtering Wireless MAC Filtering15 Add or Modify Wireless MAC Address Filtering entry To access for Filtering Rules Wireless Advanced17 The router attached wireless stations Wireless StatisticsDhcp Dhcp Settings20 Dhcp Clients List Dhcp Clients ListTo modify or delete an existing entry Address ReservationTo Reserve IP addresses Delete ForwardingVirtual Servers 25 Add or Modify a Virtual Server Entry To setup a virtual server entryPort Triggering 27 Add or Modify a Triggering Entry To assign a computer or server to be a DMZ server 3 DMZUPnP Firewall SecurityIP Filtering ¾ Enable Firewall the general firewall switch is on or offTo add/modify an IP Address filtering entry TL-WR941N/TL-WR941ND Domain Filtering Other configurations for the entries35 Add or Modify a Domain Filtering entry To Add a Domain filtering entryTo add or modify a Domain Filtering entry MAC FilteringTo add additional entries, repeat steps Static Routing38 Static Routing To add static routing entriesDynamic DNS 40 Dyndns.org Ddns SettingsSystem Tools Time SettingTo configure the system manually Firmware To configure the system automaticallyBackup & Restore Factory DefaultsPassword RebootSystem log 47 PasswordStatistics Remote ManagementTCP Statistics TableFigure A-2 PPPoE Connection Mode Appendix a FAQWant to use Netmeeting, what do I need to do? Figure A-3 MAC CloneWant to build a WEB Server on the LAN, what should I do? Figure A-5 Add or Modify a Virtual server EntryFigure A-7 Remote Management Wireless stations cannot connect to the routerTL-WR941N/TL-WR941ND Install TCP/IP component Appendix B Configuring the PCsShown in the Figure below Figure B-3 ¾ Setting IP address manuallyFigure B-4 Environmental and Physical Appendix C SpecificationsWireless GeneralAppendix D Glossary TL-WR941N/TL-WR941ND

Related manuals

Manual 113 pages 40.69 Kb