TP-Link TL-WR941ND manual To add static routing entries, Static Routing

Page 56

TL-WR941N/TL-WR941ND

Wireless N Router

Figure 4-38 Static Routing

To add static routing entries:

1. Click Add New… shown in Figure 4-38,you will see the following screen.

Figure 4-39 Add or Modify a Static Route Entry

2.Enter the following data:

¾Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.

¾Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.

¾Gateway - This is the IP Address of the gateway device that allows for contact between the router and the network or host.

3.Select Enabled or Disabled for this entry on the Status pull-down list.

4.Click the Save button to make the entry take effect.

Other configurations for the entries:

Click the Delete button to delete the entry.

Click the Enable All button to enable all the entries.

Click the Disable All button to disable all the entries.

- 51 -

Image 56

Contents TL-WR941N TL-WR941ND Copyright & Trademarks FCC Statement FCC RF Radiation Exposure Statement Country Restriction Reason/remarkContents Dhcp Package Contents Introduction Overview of the RouterMain Features ConventionsName Status Indication Panel LayoutFront Panel ¾ Reset button Rear PanelConnecting the Router Installation Environment RequirementsConnecting the Router System RequirementsHardware Installation of the TL-WR941ND Wireless N Router Quick Installation Guide TCP/IP configurationSuccess result of Ping command Please check the connection following these stepsQuick Installation Guide 3Login the routerChoose WAN Connection Type Quick Setup Static IP 10 Quick Setup Finish Status Configuring the RouterLogin Quick Setup Router StatusQuick Secure Setup function QSSBy PBC Method OneMethod Two Add a New DeviceII. By PIN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND 2 WAN Network1 LAN TL-WR941N/TL-WR941ND TL-WR941N/TL-WR941ND WAN PPPoE PPPoE Advanced Settings Wireless MAC CloneWireless Settings 12 Wireless SettingsWireless Security TL-WR941N/TL-WR941ND Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 14 Wireless MAC address Filtering15 Add or Modify Wireless MAC Address Filtering entry Wireless Advanced To access for Filtering RulesWireless Statistics 17 The router attached wireless stationsDhcp Settings DhcpDhcp Clients List 20 Dhcp Clients ListTo modify or delete an existing entry Address ReservationTo Reserve IP addresses Delete ForwardingVirtual Servers To setup a virtual server entry 25 Add or Modify a Virtual Server EntryPort Triggering 27 Add or Modify a Triggering Entry To assign a computer or server to be a DMZ server 3 DMZUPnP Security Firewall¾ Enable Firewall the general firewall switch is on or off IP FilteringTo add/modify an IP Address filtering entry TL-WR941N/TL-WR941ND Other configurations for the entries Domain FilteringTo Add a Domain filtering entry 35 Add or Modify a Domain Filtering entryMAC Filtering To add or modify a Domain Filtering entryStatic Routing To add additional entries, repeat stepsTo add static routing entries 38 Static Routing40 Dyndns.org Ddns Settings Dynamic DNSSystem Tools Time SettingTo configure the system manually To configure the system automatically FirmwareFactory Defaults Backup & RestoreReboot Password47 Password System logRemote Management StatisticsStatistics Table TCPAppendix a FAQ Figure A-2 PPPoE Connection ModeFigure A-3 MAC Clone Want to use Netmeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do?Wireless stations cannot connect to the router Figure A-7 Remote ManagementTL-WR941N/TL-WR941ND Appendix B Configuring the PCs Install TCP/IP componentShown in the Figure below ¾ Setting IP address manually Figure B-3Figure B-4 Appendix C Specifications WirelessGeneral Environmental and PhysicalAppendix D Glossary TL-WR941N/TL-WR941ND

Related manuals

Manual 113 pages 40.69 Kb