TP-Link TL-WR1043ND manual PSK Password You can enter Ascii or Hexadecimal characters

Page 23

TL-WR1043NDWireless N Gigabit Router

¾Wireless Radio - Enable or disable the wireless radio by choosing from the drop-down list.

¾SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.

¾Region - Select your region from the drop-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.

¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto, so the AP will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Mode - This field determines the wireless mode which the Router works on.

¾Channel Width - Select any channel width from the drop-down list. The default setting is automatic, which can automatically adjust the channel width for your clients.

¾Max Tx Rate - You can limit the maximum transmission rate of the Router through this field.

¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. It is strongly recommended that you choose one of following options to enable security.

¾WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase.

zPSK Password - You can enter ASCII or Hexadecimal characters.

For ASCII, the key can be made up of any numbers from 0 to 9 and any letters from A to Z, and the length should be between 8 and 63 characters.

For Hexadecimal, the key can be made up of any numbers from 0 to 9 and letters from A to F, and the length should be between 8 and 64 characters.

Please also note the key is case sensitive, which means that upper and lower case keys will affect the outcome. It would also be a good idea to write down the key and all related wireless security settings.

¾No Change - If you chose this option, wireless security configuration will not change!

These settings are only for basic wireless parameters. For advanced settings, please refer to Section 4.6: “Wireless”.

-14-

Page 22 Page 24
Image 23
Page 22 Page 24
Contents TL-WR1043ND Copyright & Trademarks FCC Statement Country Restriction Reason/remark CE Mark WarningKorea Warning Statements Yang Hongliang Product Manager of International Business Product Description Wireless N Gigabit RouterContents 10.1 Appendix a FAQ 105 Appendix B Configuring the PCs 110 Package Contents Conventions Overview of the RouterMain Features Name Status Indication Panel LayoutFront Panel Rear Panel ¾ ResetSystem Requirements Installation Environment RequirementsConnecting the Router TL-WR1043NDWireless N Gigabit Router TCP/IP Configuration Quick Installation GuidePlease check the connection following these steps Quick Installation Guide3Login the Router Choose WAN Connection Type Quick Setup MAC Clone 10 Quick Setup Static IP PSK Password You can enter Ascii or Hexadecimal characters 12 Quick Setup Finish Status LoginQSS Quick SetupMethod One By PBCMethod Two QSS Configuration Screen of Wireless Adapter Add a New Device Method ThreeII. By PIN Next TL-WR1043NDWireless N Gigabit Router 1 WAN NetworkWAN Static IP WAN PPPoE TL-WR1043NDWireless N Gigabit Router PPPoE Advanced Settings WAN BigPond Cable NSW / ACT nsw.bigpond.net.au10 WAN -L2TP TL-WR1043NDWireless N Gigabit Router 11 WAN -PPTP 12 LAN 2 LAN13 MAC Address Clone MAC CloneWireless Settings WirelessTL-WR1043NDWireless N Gigabit Router Disabled to allow wireless stations access Wireless SecurityTL-WR1043NDWireless N Gigabit Router Encryption You can select either Automatic, or Tkip or AES Wireless MAC Filtering 20 Wireless MAC address Filtering To modify or delete an existing entry Wireless Advanced Wireless Statistics Dhcp Dhcp Settings26 Dhcp Clients List Dhcp Clients ListTo Reserve IP addresses Address ReservationStorage Sharing USB Settings32Storage Sharing FTP Server 35Add or Modify Share Folder TL-WR1043NDWireless N Gigabit Router Media Server TL-WR1043NDWireless N Gigabit Router Print Server 42 Pint Server SettingTo add a new user account, please follow the steps below User AccountsTL-WR1043NDWireless N Gigabit Router Virtual Servers Forwarding47 Add or Modify a Virtual Server Entry To setup a virtual server entryTo add a new rule, follow the steps below Port Triggering49 Add or Modify a Triggering Entry Once the Router is configured, the operation is as followsTo assign a computer or server to be a DMZ server 3 DMZUPnP 51 UPnP Setting Basic Security SecurityAdvanced Security TL-WR1043NDWireless N Gigabit Router 55 Local Management Local Management56 Remote Management Remote ManagementTo add a new entry, please follow the steps below Parental Control58 Add or Modify Parental Control Entry TL-WR1043NDWireless N Gigabit Router Rule Access ControlThere are two methods to add a new rule Method One 62 Quick Setup Create a Host EntryTL-WR1043NDWireless N Gigabit Router TL-WR1043NDWireless N Gigabit Router Method Two 66 Add Internet Access Control Entry Host 67 Host Settings69 Add or Modify a Host Entry TargetTo add a new entry, please follow the steps below： 71 Add or Modify an Access Target EntrySchedule 73 Schedule SettingsTo add a new schedule, follow the steps below 74 Advanced Schedule SettingsTo add static routing entries Advanced RoutingStatic Routing List System Routing Table Other configurations for the entriesBandwidth Control Control Settings81 Bandwidth Control Rules List Rules ListBinding Settings 15 IP & MAC Binding SettingTo find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowARP List Dynamic DNSComexe.cn Ddns To set up for DDNS, follow these instructionsDyndns.org Ddns 89 Dyndns.org Ddns Settings91 The System Tools menu System Tools92 Time settings Time SettingTo set Daylight Saving DiagnosticTo set time manually To set time automaticallyTL-WR1043NDWireless N Gigabit Router 95 Diagnostic Results Firmware UpgradeBackup & Restore Factory Defaults98 Backup & Restore Configuration Reboot100 Password Password101 System Log System Log102 103 Statistics StatisticsStatistics Table TL-WR1043NDAppendix a FAQ Figure A-3 MAC Clone Want to use Netmeeting, what do I need to do?Figure A-5 Add or Modify a Virtual server Entry Want to build a WEB Server on the LAN, what should I do? Figure A-7 Basic SecurityFigure A-9 Virtual Servers Wireless stations cannot connect to the RouterInstall TCP/IP component Appendix B Configuring the PCsFigure B-2 Figure B-3 Environmental and Physical WirelessGeneral Appendix D Glossary 115
Related manuals
Manual 24 pages 16.76 Kb
Top Page Image Contents