TP-Link TD-8816 manual 4.3.2 LAN, ADSL2/2+ Ethernet Router User Guide, Bridge Mode

Page 24

4.Bridge Mode

TD-8816

ADSL2/2+ Ethernet Router User Guide

Subnet Mask and Gateway IP address.

¾Default Route: You should select Yes to configure the PVC as the default gateway to internet from this device.

¾MAC Spoofing: MAC Spoofing feature allows you to change the assigned MAC address of the ADSL Router to a different one, which may allow the bypassing of access control lists on servers either hiding a computer on a network or allowing it to impersonate another computer. You can select Enable and specify a MAC Address for the Router here, or keep the default setting as Disable.

4.Bridge Mode

If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN.

Figure 4-8

)Note:

After you finish the Internet configuration, please click SAVE to make the settings take effect.

4.3.2 LAN

Choose “Interface Setup→LAN” menu, and you will see the LAN screen (shown in Figure 4-9). Please configure the parameters for LAN ports according to the descriptions below.

18

Image 24

Contents TD-8816 ADSL2/2+ Ethernet Router Rev1.0.2 1910010149COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark WarningPackage Contents CONTENTS Chapter 2. Hardware InstallationChapter 3. Quick Installation Guide Chapter 1. IntroductionAppendix A Specification Diagnostic4.6.4 4.6.51.2 Main Features Chapter 1. Introduction1.1 Product Overview ADSL1.3 Conventions Chapter 2. Hardware Installation 2.1 The Front Panel2.2 The Back Panel LED Explanation2.3 Installation Environment 2.4 Connecting the RouterTD-8816 Chapter 3. Quick Installation Guide 3.1 Configure PCTD-8816 Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.3 Interface Setup 4.2 Quick Start4.3.1 Internet the next screen shown in Figure 1. Dynamic IP Address ¾ TCP MTU Option Enter the TCP MTU as your desirefor WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format 2. Static IP Address3. PPPoA/PPPoE TD-8816 4.3.2 LAN 4. Bridge ModeTD-8816 IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function 4.4.3.1. DMZ4.4.3.2. Virtual Server Other configurations for the entries as shown in Figure Server in the next screenTo add a virtual server entry 4.4.3.3. IP Address Mapping To add a mapping rule4.4.4 QoS 4.4.5 VLAN can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows 1. Assign VLAN PVID for each Interface2. Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1. IP Filter¾ Interface Select the interface for the entry ¾ Rule Type For IP Filter, please select IP here To add an IP Address filtering entryStep 5 Finally, click the SAVE to save the entry 4.5.2.2. MAC FilterTo add a MAC Address filtering entry Step 4 Finally, click the SAVE to save the entry 4.5.2.3. Application Filter¾ Application Filter Activate or deactivate the function 4.5.2.4. URL4.5.3 SNMP To add a URL filter entry4.5.4 UPnP 4.5.5 DDNS4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration4.6.2 Time Zone 1. NTP Server automatically4.6.3 Firmware 2. PC’s Clock3. Manually To upgrade the routers firmware, follow these instructions below 4 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings 4.6.4 System Restart To restore the Router’s settings4.6.5 Diagnostic 4.7 HelpTD-8816 Appendix A Specification GeneralPhysical and Environment

Related manuals

Manual 73 pages 34.79 Kb

Manual 67 pages 35.92 Kb

Manual 54 pages 55.13 Kb