TP-Link TD-8816 manual ADSL2/2+ Ethernet Router User Guide, Url

Page 44

¾Application Filter: Activate or deactivate the function.

TD-8816

ADSL2/2+ Ethernet Router User Guide

Figure 4-29

¾Filter Type Selection: Select the Application Filter for the next configuration.

¾Application Filter: Activate or deactivate the function.

¾ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application.

4.5.2.4. URL

Select URL as the Filter type (shown in Figure 4-30),then you can configure the filter rules based on URL.

38

Image 44

Contents TD-8816 ADSL2/2+ Ethernet Router Rev1.0.2 1910010149COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark WarningPackage Contents CONTENTS Chapter 2. Hardware InstallationChapter 3. Quick Installation Guide Chapter 1. IntroductionAppendix A Specification Diagnostic4.6.4 4.6.51.2 Main Features Chapter 1. Introduction1.1 Product Overview ADSL1.3 Conventions Chapter 2. Hardware Installation 2.1 The Front Panel2.2 The Back Panel LED Explanation2.3 Installation Environment 2.4 Connecting the RouterTD-8816 Chapter 3. Quick Installation Guide 3.1 Configure PCTD-8816 Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 1 Is the connection between your PC and the Router correct? 3.2 Login2 Is the TCP/IP configuration for your PC correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.3.1 Internet 4.3 Interface Setup4.2 Quick Start the next screen shown in Figure 1. Dynamic IP Address ¾ TCP MTU Option Enter the TCP MTU as your desire3. PPPoA/PPPoE for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format2. Static IP Address TD-8816 4.3.2 LAN 4. Bridge ModeTD-8816 IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4.2 Routing 4.4 Advanced Setup4.4.1 Firewall 4.4.3 NAT 4.4.3.2. Virtual Server ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function4.4.3.1. DMZ To add a virtual server entry Other configurations for the entries as shown in FigureServer in the next screen 4.4.3.3. IP Address Mapping To add a mapping rule4.4.4 QoS 4.4.5 VLAN 2. Define VLAN Group can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows1. Assign VLAN PVID for each Interface 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1. IP Filter¾ Interface Select the interface for the entry ¾ Rule Type For IP Filter, please select IP here To add an IP Address filtering entryStep 5 Finally, click the SAVE to save the entry 4.5.2.2. MAC FilterTo add a MAC Address filtering entry Step 4 Finally, click the SAVE to save the entry 4.5.2.3. Application Filter¾ Application Filter Activate or deactivate the function 4.5.2.4. URL4.5.3 SNMP To add a URL filter entry4.5.4 UPnP 4.5.5 DDNS4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration4.6.2 Time Zone 1. NTP Server automatically3. Manually 4.6.3 Firmware2. PC’s Clock To back up the Router’s current settings To upgrade the routers firmware, follow these instructions below4 The router will reboot after the upgrading has been finished 4.6.4 System Restart To restore the Router’s settings4.6.5 Diagnostic 4.7 HelpTD-8816 Physical and Environment Appendix A SpecificationGeneral

Related manuals

Manual 73 pages 34.79 Kb

Manual 67 pages 35.92 Kb

Manual 54 pages 55.13 Kb