TP-Link TD-8816 ADSL2/2+ Ethernet Router User Guide, Finally, click the SAVE to save the entry

Page 43
Step 4: Finally, click the SAVE to save the entry.

TD-8816

ADSL2/2+ Ethernet Router User Guide

select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule.

)Note:

If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”.

Step 4: Finally, click the SAVE to save the entry.

Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address 00-0A-EB-00-07-5F to access the Internet.

)Note:

After you complete the MAC filter rules for the example, the Filter list will show as follows. You can enter the IP / MAC Filter Set Index to view the information about the rule.

Other configurations for the entries as shown in Figure 4-27:

Enter the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry.

Enter the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry.

4.5.2.3. Application Filter

Select Application Filter as the Filter type (shown in Figure 4-29),then you can configure the filter rules based on application.

37

Image 43
Contents Rev1.0.2 1910010149 TD-8816 ADSL2/2+ Ethernet RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTPackage Contents Chapter 1. Introduction CONTENTSChapter 2. Hardware Installation Chapter 3. Quick Installation Guide4.6.5 Appendix A SpecificationDiagnostic 4.6.4ADSL 1.2 Main FeaturesChapter 1. Introduction 1.1 Product Overview1.3 Conventions LED Explanation Chapter 2. Hardware Installation2.1 The Front Panel 2.2 The Back Panel2.4 Connecting the Router 2.3 Installation EnvironmentADSL2/2+ Ethernet Router User Guide 3.1 Configure PC Chapter 3. Quick Installation GuideADSL2/2+ Ethernet Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start 4.1 Status Chapter 4. Software Configuration4.2 Quick Start 4.3 Interface Setup4.3.1 Internet the next screen shown in Figure ¾ TCP MTU Option Enter the TCP MTU as your desire 1. Dynamic IP Address2. Static IP Address for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format3. PPPoA/PPPoE ADSL2/2+ Ethernet Router User Guide 4. Bridge Mode 4.3.2 LANADSL2/2+ Ethernet Router User Guide IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.1. DMZ ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function4.4.3.2. Virtual Server Server in the next screen Other configurations for the entries as shown in FigureTo add a virtual server entry To add a mapping rule 4.4.3.3. IP Address Mapping4.4.4 QoS 4.4.5 VLAN 1. Assign VLAN PVID for each Interface can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows2. Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2.1. IP Filter 4.5.2 Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry ¾ Rule Type For IP Filter, please select IP here4.5.2.2. MAC Filter Step 5 Finally, click the SAVE to save the entryTo add a MAC Address filtering entry 4.5.2.3. Application Filter Step 4 Finally, click the SAVE to save the entry4.5.2.4. URL ¾ Application Filter Activate or deactivate the functionTo add a URL filter entry 4.5.3 SNMP4.5.5 DDNS 4.5.4 UPnP4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance1. NTP Server automatically 4.6.2 Time Zone2. PC’s Clock 4.6.3 Firmware3. Manually 4 The router will reboot after the upgrading has been finished To upgrade the routers firmware, follow these instructions belowTo back up the Router’s current settings To restore the Router’s settings 4.6.4 System Restart4.7 Help 4.6.5 DiagnosticADSL2/2+ Ethernet Router User Guide General Appendix A SpecificationPhysical and Environment
Related manuals
Manual 73 pages 34.79 Kb Manual 67 pages 35.92 Kb Manual 54 pages 55.13 Kb