TP-Link TD-8816 manual Package Contents

Page 4

Package Contents

The following items should be found in your package:

¾One TD-8816 ADSL2/2+ Ethernet Router

¾One AC power Adapter for TD-8816 ADSL2/2+ Ethernet Router

¾Quick Installation Guide

¾One RJ45 cable

¾Two RJ11 cables

¾One ADSL splitter

¾One Resource CD , including: z This User Guide

z Other Helpful Information

)Note:

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.

Image 4

Contents TD-8816 ADSL2/2+ Ethernet Router Rev1.0.2 1910010149COPYRIGHT & TRADEMARKS FCC STATEMENT CE Mark WarningPackage Contents CONTENTS Chapter 2. Hardware InstallationChapter 3. Quick Installation Guide Chapter 1. IntroductionAppendix A Specification Diagnostic4.6.4 4.6.51.2 Main Features Chapter 1. Introduction1.1 Product Overview ADSL1.3 Conventions Chapter 2. Hardware Installation 2.1 The Front Panel2.2 The Back Panel LED Explanation2.3 Installation Environment 2.4 Connecting the RouterTD-8816 Chapter 3. Quick Installation Guide 3.1 Configure PCTD-8816 Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.2 Quick Start 4.3 Interface Setup4.3.1 Internet the next screen shown in Figure 1. Dynamic IP Address ¾ TCP MTU Option Enter the TCP MTU as your desire2. Static IP Address for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format3. PPPoA/PPPoE TD-8816 4.3.2 LAN 4. Bridge ModeTD-8816 IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4.1 Firewall 4.4 Advanced Setup4.4.2 Routing 4.4.3 NAT 4.4.3.1. DMZ ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function4.4.3.2. Virtual Server Server in the next screen Other configurations for the entries as shown in FigureTo add a virtual server entry 4.4.3.3. IP Address Mapping To add a mapping rule4.4.4 QoS 4.4.5 VLAN 1. Assign VLAN PVID for each Interface can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows2. Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL4.5.2 Filter 4.5.2.1. IP Filter¾ Interface Select the interface for the entry ¾ Rule Type For IP Filter, please select IP here To add an IP Address filtering entryStep 5 Finally, click the SAVE to save the entry 4.5.2.2. MAC FilterTo add a MAC Address filtering entry Step 4 Finally, click the SAVE to save the entry 4.5.2.3. Application Filter¾ Application Filter Activate or deactivate the function 4.5.2.4. URL4.5.3 SNMP To add a URL filter entry4.5.4 UPnP 4.5.5 DDNS4.5.6 CWMP 4.6 Maintenance 4.6.1 Administration4.6.2 Time Zone 1. NTP Server automatically2. PC’s Clock 4.6.3 Firmware3. Manually 4 The router will reboot after the upgrading has been finished To upgrade the routers firmware, follow these instructions belowTo back up the Router’s current settings 4.6.4 System Restart To restore the Router’s settings4.6.5 Diagnostic 4.7 HelpTD-8816 General Appendix A SpecificationPhysical and Environment

Related manuals

Manual 73 pages 34.79 Kb

Manual 67 pages 35.92 Kb

Manual 54 pages 55.13 Kb