TP-Link TD-8816 ADSL2/2+ Ethernet Router User Guide, To back up the Router’s current settings

Page 51

To upgrade the router's firmware, follow these instructions below:

TD-8816

ADSL2/2+ Ethernet Router User Guide

drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade.

Figure 4-40

To upgrade the router's firmware, follow these instructions below:

Step 1: Download a more recent firmware upgrade file from the TP-LINK website (www.tp-link.com).

Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse button to locate the update file.

Step 3: Click the UPGRADE button.

)Note:

1)New firmware versions are posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use.

2)When you upgrade the router's firmware, you may lose its current configurations, so please back up the router’s current settings before you upgrade its firmware.

3)Do not turn off the router or press the Reset button while the firmware is being upgraded.

4)The router will reboot after the upgrading has been finished.

To back up the Router’s current settings:

Step 1: Click the ROMFILE SAVE button (shown in Figure 4-40),click Save button in the next screen (shown in Figure 4-41)to proceed.

45

Image 51

Contents Rev1.0.2 1910010149 TD-8816 ADSL2/2+ Ethernet RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTPackage Contents Chapter 1. Introduction CONTENTSChapter 2. Hardware Installation Chapter 3. Quick Installation Guide4.6.5 Appendix A SpecificationDiagnostic 4.6.4ADSL 1.2 Main FeaturesChapter 1. Introduction 1.1 Product Overview1.3 Conventions LED Explanation Chapter 2. Hardware Installation2.1 The Front Panel 2.2 The Back Panel2.4 Connecting the Router 2.3 Installation EnvironmentADSL2/2+ Ethernet Router User Guide 3.1 Configure PC Chapter 3. Quick Installation GuideADSL2/2+ Ethernet Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 5 Click NEXT to finish the Quick Start 4.1 Status Chapter 4. Software Configuration4.3 Interface Setup 4.2 Quick Start4.3.1 Internet the next screen shown in Figure ¾ TCP MTU Option Enter the TCP MTU as your desire 1. Dynamic IP Addressfor WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format 2. Static IP Address3. PPPoA/PPPoE ADSL2/2+ Ethernet Router User Guide 4. Bridge Mode 4.3.2 LANADSL2/2+ Ethernet Router User Guide IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function 4.4.3.1. DMZ4.4.3.2. Virtual Server Other configurations for the entries as shown in Figure Server in the next screenTo add a virtual server entry To add a mapping rule 4.4.3.3. IP Address Mapping4.4.4 QoS 4.4.5 VLAN can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows 1. Assign VLAN PVID for each Interface2. Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2.1. IP Filter 4.5.2 Filter¾ Interface Select the interface for the entry To add an IP Address filtering entry ¾ Rule Type For IP Filter, please select IP here4.5.2.2. MAC Filter Step 5 Finally, click the SAVE to save the entryTo add a MAC Address filtering entry 4.5.2.3. Application Filter Step 4 Finally, click the SAVE to save the entry4.5.2.4. URL ¾ Application Filter Activate or deactivate the functionTo add a URL filter entry 4.5.3 SNMP4.5.5 DDNS 4.5.4 UPnP4.5.6 CWMP 4.6.1 Administration 4.6 Maintenance1. NTP Server automatically 4.6.2 Time Zone4.6.3 Firmware 2. PC’s Clock3. Manually To upgrade the routers firmware, follow these instructions below 4 The router will reboot after the upgrading has been finishedTo back up the Router’s current settings To restore the Router’s settings 4.6.4 System Restart4.7 Help 4.6.5 DiagnosticADSL2/2+ Ethernet Router User Guide Appendix A Specification GeneralPhysical and Environment

Related manuals

Manual 73 pages 34.79 Kb

Manual 67 pages 35.92 Kb

Manual 54 pages 55.13 Kb