Peavey CS-G series, CS 3000G Front Panel Features Channels a 81 B Input Sensitivity, Power LED

Page 4

Front Panel:

FRONT PANEL FEATURES

CHANNELS A 81 B

INPUT SENSITIVITY (1)

The maximum input gain (minimum sensitivity rating) is achieved at the full clockwise setting, which yields the maximum mixer/system headroom. A setting of less than full clockwise will yield lower system noise at the expense of mixer/system headroom. Calibration indicates sensitivity in dBV necessary to attain the full available rated output power.

POWER LED (2)

Illuminates when AC power is being supplied to the amp, and the associated channel is operational. If either channel were to experience fault conditions or to exceed the safe operating temperature limits, then that channel would shut down, and the associated power LED would cease to illuminate, indicating such conditions exist. Also, whenever the Bridge mode is selected, the power LED of channel B is defeated (off), just as if there were a fault condition on channel B. This provides a positive indication that the CS 3000G is configured for Bridge mode.

DDT ACTIVE LED (3)

Illuminates when DDT Compression is taking place in that channel. With the ENABLE/DEFEAT switch in the DEFEAT position, this LED indicates when clipping distortion is occurring in that channel.

CIRCUIT BREAKERS (4)

The CS 3000G uses circuit breakers in place of main fuses. These breakers are provided to limit the current A to the associated power transformer for each channel, and thereby offer protection from overheating and possible destruction due to fault conditions in the amplifier. The breaker trip current value has been carefully chosen to allow continuous power output performance, yet still provide adequate protection for the power

A transformer. Normally, these breakers should not trip unless there is a fault in the amp circuitry that draws excessive mains current. However, abnormal conditions, such as a short circuit on either or both channels or continuous operation at overload or clipping (especially into 2 ohm load) will cause the breaker to trip. If this occurs, turn the power switch off, then simply reset the breaker and correct the cause of the overload.

When tripped, the button on the breaker will be outward nearly l/2” and can be reset by pushing inward. A normal reset button length is about l/4”. If this “thermal” type breaker does trip, simply pushing the button back in will reset it, after waiting a brief period of time to allow it to cool down. REMEMBER, ALWAYS TURN THE POWER OFF BEFORE RESETTING THE BREAKER. If the breaker trips instantly each time you attempt to reset it, the unit should be taken to a qualified service center for repair.

POWER SWITCH (5)

Depress to the “I” position to turn on.

Image 4
Contents Page Page CS@ 3000G Features Front Panel Features Channels a 81 B Input Sensitivity Power LEDPower Switch DDT Active LEDBack Panel Features Mains Power Source 6 120 V products onlyGround Lift Switch Back PanelPL-2 Selector Switch Mode SwitchDDT Compression Switch LOW-Z InputInstallation and Connection Industrial and Commercial InstallationsBridge Mode DDT CompressionOutput Power typical value Rated Output PowerPower Bandwidth typical value Power Consumption13NNWH3 13NNWH3Wiring Diagrams Caracteristicas de1 CS@ 3000G Funciones DEL Panel Frontal Canales a Y B Ground Lift Switch Interruptor levantamiento de tierra Panel TraseroFunciones DEL Panel Trasero Speaker Outputs Salidas de altavocesInstalacign Y Conexign MOD0 DE Puente INSTALACdN Industrial Y ComercialCOMPRESldN DDT Caracthistiques du CS@ 3000G Power LED DEL d’alimentation Power Switch Commutateur marche-arrQtCARACT~RISTIQUES DU Panneau Avant Canaux a ET DDT Active LED DEL d’activation du DDTGround Lift Switch Commutateur de separation de terre Speaker Outputs Sorties des haut-parleursPL-2 Selector Switch Commutateur de st5lection PL-2 Mode Switch Commutateur de modeDDT Compression Switch Commutateur de compression DDT LOW-Z Input EntrBe Low-ZInstallation ET Connexion Installation Commerciale ET IndustrielleMode Pont Compression DDTCS@ 3000G Merkmal Beschreibung DER Frontplatte Kanal a UND B Riickplatte Ground Lift Switch ErdabhebungsschalterSpeaker Outputs Lautsprecherausgiinge Aufstellung UND Anschluss Industrieller UND Kommerzieller Einsatz DDT-KOMPRESSIONPeavey ONE-YEAR Limited WARRANTY/REMEDY Important Safety Instructions #80300372