Kramer Electronics user manual Defines the rear panel of the VP-81SIDN

Page 11

VP-81SIDN – Defining the VP-81SIDN 8x1 Digital Step-In Switcher

7

Figure 2 defines the rear panel of the VP-81SIDN.

Figure 2: VP-81SIDN 8x1 Digital Step-In Switcher Rear Panel

#

 

Feature

 

 

 

Function

1

 

TP Input RJ-45 Connectors IN 1 to

 

 

Connect to the remote TP sources (1 to 8) using CAT 6 or higher specification

 

 

IN 8

 

 

 

cable. These may be step-in panels (for example, SID-DP) or TP transmitters (for

 

 

 

 

 

 

example, the PT-571 or TP-573)

2

 

LOCAL

DVI

 

 

Connect to the local DVI source

3

 

INPUTS

HDMI

 

 

Connect to the local HDMI source

 

 

 

 

 

 

 

 

 

 

 

 

4

 

TP OUT RJ-45 Connector

 

 

Connect to the remote TP receiver, for example, PT-572+, using CAT 6 or higher

 

 

 

 

 

 

specification cable (maximum 50m, 164ft)

5

 

USB POWER Connector

 

 

Connect any device requiring USB power, (for example, the Kramer KW-11T)

6

 

RS-2329-pin D-sub Port (F)

 

 

Connect to a serial controller (see Section 6.3)

 

 

 

 

 

 

 

 

 

 

7

 

REMOTE 12-way Terminal Block

 

 

Connect to remote contact closure input and output selection switches (see

 

 

 

 

 

 

Section 6.2)

 

 

 

 

 

 

 

8

 

ETHERNET RJ-45 Connector

 

 

Connect to a PC or LAN for remote control via Ethernet (see Section 6.5)

 

 

 

 

 

 

 

 

9

 

AC Mains Power Socket

 

 

Connect to the AC mains power

 

 

 

 

 

 

 

10

 

AC Mains Fuse

 

 

 

AC mains supply protection fuse

11

 

AC Mains Power Switch

 

 

Turns the AC mains power supply to the device on and off

Page 10 Page 12
Image 11
Page 10 Page 12
Contents VP-81SIDN Page Figures Remote Input Selection Switch Wiring Introduction Achieving the Best Performance Safety InstructionsGetting Started Recycling Kramer Products Overview Using the IR Transmitter for the VP-81SIDN About the Power Connect FeatureUsing Twisted Pair cables Feature Function Defining the VP-81SIDN 8x1 Digital Step-In SwitcherDefines the rear panel of the VP-81SIDN Switcher Installing in a Rack Connecting the VP-81SIDN 8x1 Digital Step-In Switcher Connecting the VP-81SIDN 8x1 Digital Step- In SwitcherPage Terminal Description Number Connecting to a Balanced Audio AcceptorRemote Input Selection Switch Wiring To connect a device with a RS-485 port to the VP-81SIDN Connecting to the VP-81SIDN via RS-485Connecting and Controlling Multiple VP-81SIDN Devices To connect to the VP-81SIDN via RS-232To connect up to four VP-81SIDN devices Connecting the Ethernet Port Directly to a PC Local Area Connection Properties Window Internet Protocol Version 6 Properties Window Control Configuration via the Ethernet Port Connecting the Ethernet Port via a Network Hub or SwitchTo select an input Operating the VP-81SIDN LocallySelecting an Input Selecting an Output Muting the Input when using Step-In CommandersResetting all Input Priorities to the Default Setting the Audio Output VolumeTo mute and unmute the audio output Locking and Unlocking the Front Panel ButtonsMuting and unmuting the Audio To lock and unlock the front panel buttonsTo read the current RS-485 machine number Configuring and Maintaining the VP-81SIDNSetting the RS-485 Device Number Reading the Current RS-485 Device NumberResetting to the Factory Default Settings Setting the RS-485 Bus TerminationUpgrading the Firmware Operating the VP-81SIDN Remotely Operating the VP-81SIDN Using the Controller SoftwareFollowing table describes the main window features Feature Description Output Volume SliderMenu Bar Sub Menu Description Options Authorized UsersStep-In Software Menu Bar To log in as admin Logging in as AdminConnecting to the Device To switch an input to an output Switching an Input to an OutputInput Selection Switching and Selecting an Input when using the VP-81SIDNTo mute the audio output Changing the Output VolumeTo change the output volume Muting the Audio OutputTo change an input/output button icon and label Changing the Priority of an InputChanging the Input and Output Button Icons and Labels Updating the Firmware Resetting the DeviceTo set the number of devices Setting the IP Network ParametersSetting Multiple Cascaded Devices VP-81SIDN Operating the VP-81SIDN Remotely Do not use a crossed TP cable with this product Wiring the DGKat TP RJ-45 ConnectorsWire Color Inputs Technical SpecificationsEthernet Default Communication ParametersRS-232 Device Message Format ProtocolKramer Protocol 3000 Syntax Host Message FormatCommand Terms Chaining Commands Kramer Protocol 3000 CommandsEntering Commands Command FormsLdfw Page Safety Warning
Top Page Image Contents