Kramer Electronics VP-81SIDN user manual Switcher

Page 12

#

Feature

Function

8

12

LOCAL AUDIO

DVI

Connect to the local DVI audio source

13

INPUTS

HDMI

Connect to the local HDMI audio source

14

HDMI OUT Connector

Connect to the local HDMI acceptor

15

+L–G+R–

Connect to the balanced audio acceptor (see Section 6.1)

16

AUDIO

R

Connect to the unbalanced audio acceptor right channel

17

OUTPUTS

L

Connect to the unbalanced audio acceptor left channel

18

S/PDIF

Connect to the digital audio acceptor

19

PROG TERM DIP-Switch

DIP-Switch 1: Sets the RS-485 bus termination (see Section 8.3).

Up = Off, Down = On (Default = On)

VP

DIP-Switch 2: For the use of Kramer service personnel only

20

RS-4853-way Terminal Block

Connect to RS-485 port on a remote controller or another VP-81SIDN.

-81SIDN

Connect: G to Ground, A to A, and B to B (see Section 6.4)

21

RESET Button

Press while power-cycling the device to reset parameters to factory default values

–

22

REMOTE IR 3.5mm Mini Jack

Connect to an external IR receiver unit for controlling the device via an IR remote

controller (see Section 3.3)

Defining the VP-81SIDN

8x1 Digital Step-In

Switcher

Image 12

Contents VP-81SIDN Page Figures Remote Input Selection Switch Wiring Introduction Safety Instructions Getting StartedAchieving the Best Performance Recycling Kramer Products Overview About the Power Connect Feature Using Twisted Pair cablesUsing the IR Transmitter for the VP-81SIDN Defining the VP-81SIDN 8x1 Digital Step-In Switcher Feature FunctionDefines the rear panel of the VP-81SIDN Switcher Installing in a Rack Connecting the VP-81SIDN 8x1 Digital Step- In Switcher Connecting the VP-81SIDN 8x1 Digital Step-In SwitcherPage Connecting to a Balanced Audio Acceptor Terminal Description NumberRemote Input Selection Switch Wiring Connecting to the VP-81SIDN via RS-485 Connecting and Controlling Multiple VP-81SIDN DevicesTo connect to the VP-81SIDN via RS-232 To connect a device with a RS-485 port to the VP-81SIDNTo connect up to four VP-81SIDN devices Connecting the Ethernet Port Directly to a PC Local Area Connection Properties Window Internet Protocol Version 6 Properties Window Connecting the Ethernet Port via a Network Hub or Switch Control Configuration via the Ethernet PortOperating the VP-81SIDN Locally Selecting an InputTo select an input Muting the Input when using Step-In Commanders Resetting all Input Priorities to the DefaultSetting the Audio Output Volume Selecting an OutputLocking and Unlocking the Front Panel Buttons Muting and unmuting the AudioTo lock and unlock the front panel buttons To mute and unmute the audio outputConfiguring and Maintaining the VP-81SIDN Setting the RS-485 Device NumberReading the Current RS-485 Device Number To read the current RS-485 machine numberSetting the RS-485 Bus Termination Resetting to the Factory Default SettingsUpgrading the Firmware Operating the VP-81SIDN Using the Controller Software Operating the VP-81SIDN RemotelyFollowing table describes the main window features Output Volume Slider Feature DescriptionAuthorized Users Step-In Software Menu BarMenu Bar Sub Menu Description Options Logging in as Admin Connecting to the DeviceTo log in as admin Switching an Input to an Output To switch an input to an outputSwitching and Selecting an Input when using the VP-81SIDN Input SelectionChanging the Output Volume To change the output volumeMuting the Audio Output To mute the audio outputChanging the Priority of an Input Changing the Input and Output Button Icons and LabelsTo change an input/output button icon and label Resetting the Device Updating the FirmwareSetting the IP Network Parameters Setting Multiple Cascaded DevicesTo set the number of devices VP-81SIDN Operating the VP-81SIDN Remotely Wiring the DGKat TP RJ-45 Connectors Wire ColorDo not use a crossed TP cable with this product Technical Specifications InputsDefault Communication Parameters RS-232Ethernet Protocol Kramer Protocol 3000 SyntaxHost Message Format Device Message FormatCommand Terms Kramer Protocol 3000 Commands Entering CommandsCommand Forms Chaining CommandsLdfw Page Safety Warning