Kramer Electronics VP-81SIDN user manual Output Volume Slider, Feature Description

Page 32

#

Feature

 

Function

9

Output Volume Slider

 

Click, hold and move the slider up (higher) or down (lower) to

 

 

 

adjust the output volume (see Section 9.2)

 

 

 

 

 

 

10

Mute on/off Button

 

Click to mute/unmute the output volume (see Section 9.2)

 

 

 

 

 

 

 

 

Note: When a change is made on the device (for example, a different output is selected), the change is reflected almost immediately in the main window of the Step-in Software, and visa versa.

Figure 13 shows a typical input button.

Figure 13: Typical Input Button

The following table describes the Button characteristics.

 

#

 

 

Feature

 

 

 

Description

 

 

 

 

 

 

 

 

1

 

10

 

 

 

Input (1–10) or output (1–2) channel number

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

HDMI Label

 

 

 

User-selectable button label, Admin only (see Section 9.1.1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

Status ACTIVE

 

 

 

Indicates the status of the connection and signal on the

 

 

 

 

 

 

 

 

 

channel:

 

 

 

 

 

 

 

 

 

TIMEOUT—no cable

 

 

 

 

 

 

 

 

 

MUTE— cable present, no signal detected

 

 

 

 

 

 

 

 

 

WAIT— cable and signal present but channel is not selected

 

 

 

 

 

 

 

 

 

ACTIVE—cable and signal present and channel is selected

 

 

 

 

 

 

 

 

 

(only one channel at a time)

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

User-selectable icon selected to be displayed on the button,

 

 

 

 

 

 

 

 

 

Admin only (see Section 9.4)

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

HDMI

 

 

 

Video input type: VGA, HDMI, DP, DVI

 

 

 

 

 

 

 

 

 

 

 

6

 

1280x720p@60

 

 

 

Video resolution, i=interlace/p=progressive, refresh rate

 

 

 

 

 

 

 

 

 

 

7

 

 

Priority 10 Slider

 

 

 

Slider for adjusting the priority (1, lowest–10, highest) of the

 

 

 

 

 

 

 

 

 

input, Admin only (see Section 9.3)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

VP-81SIDN - Operating the VP-81SIDN Remotely

 

 

Image 32
Contents VP-81SIDN Page Figures Remote Input Selection Switch Wiring Introduction Achieving the Best Performance Safety InstructionsGetting Started Recycling Kramer Products Overview Using the IR Transmitter for the VP-81SIDN About the Power Connect FeatureUsing Twisted Pair cables Defining the VP-81SIDN 8x1 Digital Step-In Switcher Feature FunctionDefines the rear panel of the VP-81SIDN Switcher Installing in a Rack Connecting the VP-81SIDN 8x1 Digital Step- In Switcher Connecting the VP-81SIDN 8x1 Digital Step-In SwitcherPage Connecting to a Balanced Audio Acceptor Terminal Description NumberRemote Input Selection Switch Wiring Connecting to the VP-81SIDN via RS-485 Connecting and Controlling Multiple VP-81SIDN DevicesTo connect to the VP-81SIDN via RS-232 To connect a device with a RS-485 port to the VP-81SIDNTo connect up to four VP-81SIDN devices Connecting the Ethernet Port Directly to a PC Local Area Connection Properties Window Internet Protocol Version 6 Properties Window Connecting the Ethernet Port via a Network Hub or Switch Control Configuration via the Ethernet PortTo select an input Operating the VP-81SIDN LocallySelecting an Input Muting the Input when using Step-In Commanders Resetting all Input Priorities to the DefaultSetting the Audio Output Volume Selecting an OutputLocking and Unlocking the Front Panel Buttons Muting and unmuting the AudioTo lock and unlock the front panel buttons To mute and unmute the audio outputConfiguring and Maintaining the VP-81SIDN Setting the RS-485 Device NumberReading the Current RS-485 Device Number To read the current RS-485 machine numberSetting the RS-485 Bus Termination Resetting to the Factory Default SettingsUpgrading the Firmware Operating the VP-81SIDN Using the Controller Software Operating the VP-81SIDN RemotelyFollowing table describes the main window features Output Volume Slider Feature DescriptionMenu Bar Sub Menu Description Options Authorized UsersStep-In Software Menu Bar To log in as admin Logging in as AdminConnecting to the Device Switching an Input to an Output To switch an input to an outputSwitching and Selecting an Input when using the VP-81SIDN Input SelectionChanging the Output Volume To change the output volumeMuting the Audio Output To mute the audio outputTo change an input/output button icon and label Changing the Priority of an InputChanging the Input and Output Button Icons and Labels Resetting the Device Updating the FirmwareTo set the number of devices Setting the IP Network ParametersSetting Multiple Cascaded Devices VP-81SIDN Operating the VP-81SIDN Remotely Do not use a crossed TP cable with this product Wiring the DGKat TP RJ-45 ConnectorsWire Color Technical Specifications InputsEthernet Default Communication ParametersRS-232 Protocol Kramer Protocol 3000 SyntaxHost Message Format Device Message FormatCommand Terms Kramer Protocol 3000 Commands Entering CommandsCommand Forms Chaining CommandsLdfw Page Safety Warning