Peavey JSX 212 Cabinet Impedance Switch, Speaker Outputs, Line OUT Level, HIGH/LOW Power Switch

Page 12

31

34 32

30 29

CAUTION

FUSE

33

28

(28)CABINET IMPEDANCE SWITCH

This three-position switch allows appropriate selection of speaker cabinet impedance. If two enclosures of equal impedance are used, the switch should be set to half the individual value. For example, two 16 ohm enclosures necessitate an 8 ohm setting, while two 8 ohm enclosures would require a 4 ohm setting. Minimum speaker impedance is 4 ohms.

(29)SPEAKER OUTPUTS

These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Again, minimum speaker impedance is 4 ohms. The CABINET IMPEDANCE SWITCH (28) should be set to match the load of the speaker cabinet(s).

(30)LINE OUT LEVEL

This control sets the level of signal being sent out of the LINE OUT (31) jack. It may be used to balance the level of slave power amp/speaker systems driven from the LINE OUT (31) to the level of cabinets driven from the SPEAKER OUTPUTS (29).

(31)LINE OUT

This 1/4" mono (TS) jack provides a post-power amp signal to drive another power amp/speaker system while maintaining the amplifier’s tone.

(32)HIGH/LOW POWER SWITCH

This switch allows the user to change the available output power of the amplifier from the standard full power output rating (HIGH) to a lower power output (LOW) for venues that require lower volume levels or for players who prefer high levels of distortion from the power amplifier section at lower volumes.

(33)FUSE

A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, it should be taken to a qualified service center for repair.

WARNING: THE FUSE SHOULD ONLY BE REPLACED AFTER THE POWER CORD HAS BEEN DISCONNECTED.

(34)GROUND POLARITY SWITCH

This three-position, rocker-type switch should normally be placed in the center (0) position. If hum or noise is noticed coming from the speaker enclosure(s), the switch may be placed in the “+” or “-” position to minimize hum/noise. If changing the polarity does not alleviate the problem, consult your

authorized Peavey dealer, the Peavey factory or a qualified service technician.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents JSX 212Joe Satriani Signature All-Tube Amplifier Page Important Safety Instructions Bewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones English O N T PA N E L Volume FAT SwitchTreble Noise GateChannel Select Switch High Gain InputLOW Gain Input A R PA N E L Cabinet Impedance Switch HIGH/LOW Power SwitchGround Polarity Switch Speaker OutputsIEC Mains Connector Domestic AC Mains CordCable Connector Clean SelectorO T S W I T C H ULTRA/CRUNCH SelectorJSX 212 Block Diagram JSX212 Español PA N E L F R O N TA L Volumen AgudosMedios GravesEntrada DE Ganancia Alta Entrada DE Ganancia BajaInterruptor DE Selección DE Canal PA N E L T R a S E R O Interruptor DE Impedancia Impedancia Salidas DE AltavocesNivel DE Salida DE Linea Salida DE LineaConector Principal IEC Cable DE Corriente Domestico EN EeuuSelector Clean D a LConector DE Cable Selector Ultra / CrunchJSX 212 Diagrama en Bloque JSX Français PA N N E a U AVA N T Selecteur D’ALIMENTATIONSelecteur DE Circuit DE Chauffe Standby Lampe DE StatutMediums Leds D’INDICATION DE Canal ActifSelecteur DE Canal Remote Switch Pedalier PA N N E a U a R R I È R EControle DE Niveau D’ENVOI D’EFFETS Effects Send Level 23/24 Boucle D’EFFETS Effects Send / Effects ReturnSelecteur D’IMPEDANCE D’ENCEINTE Sorties HAUTS-PARLEURSControle DE Sortie Ligne Line Level Sortie Ligne Line OUTConnecteur IEC Selecteur DE Canal Clair Clean D a L I E RConnecteur Cable DIN Selecteur Ultra / CrunchJSX 212 Diagrama en Bloque Section Amplificateur DE Puissance Deutsch Power POWER-ANZEIGER D E R S E I T E StandbyFAT-SCHALTER HIGH-GAIN-EINGANG LOW-GAIN-EINGANGCHANNEL-SCHALTER C K S E I T E EFFECTS-SEND-PEGEL23/24 Effects Send / Effects Return EFFECTS-RETURN-PEGELCabinet Impedance HIGH/LOW-LEISTUNGSSCHALTERFuse Netzsicherung Ground PolarityIEC-NETZSTECKER Hinweis NUR FÜR GrossbritannienCLEAN-WAHLSCHALTER S S S C H a LT E RRemote Cable ULTRA/CRUNCH-WAHLSCHALTERJSX 212 Block Diagram Technische Daten Peavey Electronics Corporation Limited Warranty 80304951
Top Page Image Contents