Elo TouchSystems AMM18TK2 manual Power Management Function, Stand-by Mode, Suspend Mode, Off Mode

Page 16

16User’s Guide

POWER MANAGEMENT FUNCTION

The monitor is equipped with the power management function which automatically reduce the power consumption when not in use in three power level modes.

•Stand-by Mode

The monitor goes into stand-by mode when the horizontal sync signal is off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the horizontal sync signal is restored.

•Suspend Mode

The monitor goes into suspend mode when the vertical sync signal is off for about 10 seconds. The power consumption during this is less than 8 W. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical sync signal is restored.

•Off Mode

The monitor goes into power-off mode when the vertical and horizontal sync signals are off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal sync signals are restored.

Power Management System

The AMM170TK2,AMM17TK2, AMM18TK2, AMM19TK2 andAMM19TK2/HB Medical Monitor complies with the VESA DPMS power management proposal. The VESA DPMS proposal provides four phases of power-saving modes by detecting the horizontal sync signal as shown in the table blow.

Mode

DC Input Power

AC Input power

LED Status

 

(monitor only)

(Incl. AC adapter)

 

 

 

 

 

On

35 W max.

60 W max.

Steady Green

 

 

 

 

Standby

4.5 W max.

6 W max.

Blinking Green

 

 

 

 

Supend

4.5 W max.

6 W max.

Blinking Green

 

 

 

 

Off

4.5 W max.

6 W max.

Blinking Green

 

 

 

 

When the monitor is power saving mode or detects an incorrect timing, the screen will be blank and power LED indicator will blink.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Back of the monitor Revision ControlTable of Contents Screen Adjustment Procedure To change the resolution to its factory recommended presetPress Properties to execute the Display Properties To change the resolution to its factory recommended preset Press the Auto button on the monitor Introduction Product Description and Intended UseProduct Description Warranty is void if any of these warnings are disregarded Do not Sterilize Monitor User’s Guide Symbol Definitions EU Declaration of Conformity for Medical Applications Screen Position Adjustment Safety Precaution Cleaning Your MonitorPreset Modes Ode Resolution H x Freq. KHz Freq. HzPower Management Function Stand-by ModeSuspend Mode Off ModeDDC InstallationSteps Connecting to a Television Signal Video and SoundFront Panel Controls User ControlsStandard OSD Operation OSD Scren Basic Section VGA Push the select button to execute the Zoom function OSD Scren Basic Section DVI OSD Scren Basic Section DVI OSD Scren Basic Section C-Video or S-Video Push the select button to execute Recall OSD Function Description Under Analog Display Ite m Function De s criptionOSD Function Description Under Digital Display OSD Function Description Under C-Video or S-Video Display Troubleshooting LED OFFSpecification AMM170TK2AMM17TK2 AMM18TK2 AMM19TK2 AMM19TK2/HB Classification User’s Guide AMM170TK2/AMM17TK2/AMM18TK2/AMM19TK2/AMM19TK2HB User’s Guide AMM170TK2, AMM17TK2, AMM18TK2, AMM19TK2HB VideoInput ConnectorsTouch Port Commencement and Duration of Warranty Place of Repair or ReplacementLimitation of Warranty Touch ScreenInstallation Technical Assistance ServiceQuick Start Touchmonitor installation Cable Connection AMM170TK2/AMM17TK2/AMM18TK2/AMM19TK2/AMM19TK2HB
Top Page Image Contents